Jump to content
SAU Community

Nistune Powerfc Hks Fcon Haltech Ems Link Ecu Etc Real Time Road Tune And Dyno Tune Available In Sydney And Other State


Recommended Posts

Just had my Stagea ecu done by Toshi

can confirm that it works, for sure

interstate job, so we havent met face to face nor has he seen the car

he got in an adapter, a large ecu chip that he did his majik on, and arranged (for me, so happy!) to have the adapter properly installed when my local mojo's didnt want to do it.

got the ecu back in time (today) for my dyno tune of safc/sitc tomorrow.

feels good to drive atm, the retune on dyno of the piggybacks will make it awesome Im sure

Hey Toshi.

I live in Sydney and have an R34 GTT.

Its stock but will a remap have any benifits?

And how much?

Thanks mate.

Dave

Edited by wisey18

Hi Dave

How is muffler?

All stock?

I think you need boost controller.

Normaly about 15kw-20kw more than std ecu.

You will get 185kw-200kw at 10-13psi.

Thank you

Hey Toshi.

I live in Sydney and have an R34 GTT.

Its stock but will a remap have any benifits?

And how much?

Thanks mate.

Dave

Hi Dave

How is muffler?

All stock?

I think you need boost controller.

Normaly about 15kw more than std ecu.

Thank you

Muffler is stock.

Havn't got a boost controller yet but will be getting one.

OK

Please fit boost controller.

If you fit turbo back muffler and hi flow cat you are able to get around 195kw at 10psi-11psi.

Muffler is stock.

Havn't got a boost controller yet but will be getting one.

hey toshi

i have an rb25det r33 skyline series 1 with following mods going in next week

Garrett GT30R (GT30/40), custom top mount manifold, dump pipe and ext wastegate

sard fuel preasure regulator

sard 550cc injectors

z32 afm

car already contains front mount, full exhaust , bigger fuel pump.

all i am mising is a good tune..can you do this or would i best off using a apexi power fc

i am located in sydney, parramatta. cheers

Yes, I am able to remap.

Cost road tune$550.

RB25DET std engin is up to 370, 380 hp (about 280KW) safe.

If you want to more power I think you need change after market engine parts (piston , crank shaft etc).

If you change to smaller turbo you do not need change injector. (RB25det injecter is up to 360 370 hp max)

Is this race car?

Toshi

hey toshi

i have an rb25det r33 skyline series 1 with following mods going in next week

Garrett GT30R (GT30/40), custom top mount manifold, dump pipe and ext wastegate

sard fuel preasure regulator

sard 550cc injectors

z32 afm

car already contains front mount, full exhaust , bigger fuel pump.

all i am mising is a good tune..can you do this or would i best off using a apexi power fc

i am located in sydney, parramatta. cheers

no it is not a race car just street. i dont want to rebuild engine yet so i will be happy for about 260kw can you achive this?. i want the boost to come on early so not much lag can you do tune for this? pm me your mobile number if you can thanks toshi

hi toshi

i've got r33 s1 wit the following mods

front mount.boost controller.turbo back exhuast.safcii.splitfires coils.fuel pump.

gt30/76 and the only problems is its an auto.can you do anything?cheers tony

Yes, I can remap.

How is AFM?

Is this Z32?

hi toshi

i've got r33 s1 wit the following mods

front mount.boost controller.turbo back exhuast.safcii.splitfires coils.fuel pump.

gt30/76 and the only problems is its an auto.can you do anything?cheers tony

  • 4 weeks later...

R34 ECU map

R34 can not boosted up more than around 12psi.

Because ignition timing will retard around 12psi.

Its same R33.

Also if you will boosted up around 12psi , engine will ping at around 3600-4400rpm.

Because R34 std ecu ignition map is 3600-4400rpm very hi ignition timing for Australia fuel.

  • 4 weeks later...

Hi Toshi,

Since the Brisbane trip is a bit complicated with needing to do cars during the work week and you needing to fly up here. What other options do we have? ie. retune by mail?

I need some sort of retune as my car pings if I apply throttle hard between 3500 and 4500 rpm.

Running 10 psi, full exhaust, R34 intercooler, filter and walbro pump.




  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...