Jump to content
SAU Community

Recommended Posts

Hi Guys,

Can any kind soul in Mlebourne can recommend a reliable workshop for me to change my automatic 96' R33 GTST skyline to a manual one. BTW... any ideas how much would that cost if i am juz after a simple one nothing fancy like 40% heavy duty, short shift or 3 plate stuff.....etc

Thanks..

Link to comment
https://www.sau.com.au/forums/topic/21150-where-to-do-manual-conversion/
Share on other sites

Wouldn't it be cheaper to sell it as is and buy a manual one?

Not to mention once you do that modification, your insurance (and anyone who you sell it to) will be a bit hazy cause its a major change to the car - Ie you cant call it a manual gts-t legally, you have to call it a auto converted to manual gts-t...

Well,

Leewah from ICE Performance won the dyno comp on recent Melb Autosalon. So they must know skylines well.

I did a manual conversion with ICE Performance, fitted with Daiken Organic Clutch. Car drives well and nicer than when it was with auto box.

Freeplug:

ICE Performance (03) 9512 7591

Ask for Gerald or Nigel or you can pm leewah on this forum too.

Regarding insurance, I informed Just Car that I put in manual gearbox in my auto R33, so no hassles with them.

Good luck mate.

Rianto

Originally posted by Raza

but i will still keep the auto box.

better for big hp...

but im only thinking about the drag strip.

if u like to drift.. manual all the way.unless u own a commo

because people who own auto commo think they were built for drift racing..

?? so auto is better for drags?

Originally posted by Raza

but i will still keep the auto box.

better for big hp...

but im only thinking about the drag strip.

if u like to drift.. manual all the way.unless u own a commo

because people who own auto commo think they were built for drift racing..

?? so auto is better for drags?

Are u referring to the sub-zero's auto GTS-t?

I think their gts-t doesn't use the factory auto box, think it was a 3-speed special auto gearbox made by an australian transmission specialist... can't remember the name tho.

U might b able to strengthen ur auto box for about $1500-2000, but I doubt you'll get to 10s with that. Even the manual ones may need straight cut gearboxes like Trust etc if u wanna achieve that performance.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
    • Yeah, I don't believe the M35 uses a deadhead system.
    • Have you done your thinking backwards? 3 bar, 43.5 psi pressure drop being the presumed specification for an injector, means you need 3 bar upstream when they are firing into atmospheric pressure, and more upstream pressure than that when on boost (you add your boost to your rail pressure to maintain 3 bar across the injector) and you need..... less pressure upstream when you have vacuum in the manifold. So, presuming that you're idling at -10 psi, then you only need ~23 psi in the rail. I realise that I did not need to say all of that to you specifically Matt, once you'd realised your mistake. It's mostly there for complete clarity for others.
    • Have you reached out to the guys at Spool Imports? They are a Ross dealer, I can imagine they would have the rings just sitting on the shelf (I could be wrong).  
×
×
  • Create New...