Jump to content
SAU Community

Recommended Posts

Item: N1 RB26 Conrods

Age: ~25,000kms

Condition: Perfect

Price: $200

Location: Perth

Contact: Paul - PM or 0402418697

Comments: Came out of a perfect N1 RB26 crate motor, motor was stripped down for more power, and rods replaced.

Item: N1 RB26 Pistons

Age: ~25,000kms

Condition: Perfect

Price: $50

Item: N1 RB26 Cams (believe they are 255/8.5mm, fair whack bigger than standard)

Age: ~25,000kms

Condition: Perfect

Price: $250

Item: N1 RB26 Cam Gears

Age: ~25,000kms

Condition: Perfect

Price: $50

Also have other items like head studs and valve springs if anyone's chasing them.

Link to comment
https://www.sau.com.au/forums/topic/211879-n1-rb26-engine-bits/
Share on other sites

Pistons are Sold. They are 86mm, and I have no idea how they are different from a standard one, they just came out of an R34 N1 crate motor (believe they are strengthened with better rings?). I can source standard RB26 pistons for a similar price if anyone else is interested.

Rods and Cams are under offer.

Why do you want pics of the rods? They look like standard RB26 conrods, seen one seen them all.

These parts are listed by Nissan as "semi-forged", which is crap cause its either forged or cast. I'm guessing this is Nissans code for strengthened (shotpeened/cryo'd etc).

As said, all parts are straight out of an R34 N1 motor that was in my R33.

First come first serve, if the offer for the rods / cams falls through, the next person who PM's me about them gets them.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...