Jump to content
SAU Community

Recommended Posts

When accelerating in second gear form 60 to 100 sometimes theres a slight flat spot at the 80Km mark.

I have a 93 R33 manual Exhaust blow off valve.

I thought this may becauce of the exhaust and/or blow off valve

but I noticed this on another skyline I test drove a dead stock 95 r33 man.

I have only owned the car a couple of months and I am new to turbo cars. Is this normal? or do I have a fault?

Link to comment
https://www.sau.com.au/forums/topic/21267-flat-spot/
Share on other sites

Probably just the way the stock fuel maps are setup in the ECU - if you wish to reduce it you will need a method by which you can adjust the air/fuel mixtures at particular revs... most use a S-AFC, piggy back ECU, or aftermarket ECU to do this. Hope that helps..

Link to comment
https://www.sau.com.au/forums/topic/21267-flat-spot/#findComment-448885
Share on other sites

If you get a boost controller you will probably need some sort of fuel cut defender or you will get an even bigger flat spot. Do any electronic boost controllers have these? My Profec B doesn't, the car came with a HKS fuel cut defender as well and it works perfectly.

Link to comment
https://www.sau.com.au/forums/topic/21267-flat-spot/#findComment-456543
Share on other sites

Guest Robo's

Mines got a bit of a flat spot too, sort of surges abit, its running way too rich as it backfires sometimes too. But sometimes it will pull all the way, but when it gets warmer (motor, airflow) it gets more consistant. First im going to try a cold air intake, as when i pop the bonnet and put my hand over the pod, it is very hot.

Link to comment
https://www.sau.com.au/forums/topic/21267-flat-spot/#findComment-467813
Share on other sites

Yepp - this is very typical from the R33's.

You should see my dyno run !! Big dip in power when the ECU pulls timing and dumps fuel at about 4-5000 rpm :)

The S-AFC will help. It fools the ECU and shows the ECU a reduced air flow rate, therefore the ECU doesn't pull as much timing blah blah blah.

J

Link to comment
https://www.sau.com.au/forums/topic/21267-flat-spot/#findComment-467849
Share on other sites

has happened with my rb30 as well hehehe

what it sounds like is mainly ur afm

im not too sure about the right setting for a rb25 , but with a rb30 , the air flow meter , needs to read a set ohmage of 382ohms , this measurement is taken from the 2 outer most pins on the afm , where the loom plug connects to it.

if its out it dummys info to the computer which is not correct and makes it run rich/lean etc , causes flatspots and hesitation etc etc etc.

also things like malpassi rising rate regulators can do it too , as boost hits , the fuel pressure rate rises at whatever rate the reg is (1.5:1) etc and that sudden fuel dump doesnt immediately get burnt , bit of a dull spot.

Link to comment
https://www.sau.com.au/forums/topic/21267-flat-spot/#findComment-468863
Share on other sites

  • 3 weeks later...

Robo's Yours sounds exactly the same as mine.

Have you tried a smaller gap on your plugs yet?

Unfortunatly I live out in the country and I am the only one in town with a r33 gtst so I cant swap the air flow meter with someone.

Anyone else had this problem and solved it (cant afford SAFC).

Link to comment
https://www.sau.com.au/forums/topic/21267-flat-spot/#findComment-500311
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...