Jump to content
SAU Community

Recommended Posts

  • Replies 110
  • Created
  • Last Reply

Top Posters In This Topic

Great work with your build. Its refreshing to see someone sharing their assembly process with such detail.

Now when someone has RB26/30 buld questions they can just come to your thread instead of being flamed for not using the search button (which produces more BS than real useful information).

Do you have a purpose in mind for the car? Drag, street, track or all of the above?

Hi, just wondering if you have felt the clutch yet, im looking at having to remove the clutch booster to fit my plenum. Also why did you go for the integra master cylinder instead of the original one?Was it due to the fact the stocker doesn't have provision for a fork?

Hi, just wondering if you have felt the clutch yet, im looking at having to remove the clutch booster to fit my plenum. Also why did you go for the integra master cylinder instead of the original one?Was it due to the fact the stocker doesn't have provision for a fork?

the clutch feels fine..i don't feel a different without the booster

Great work with your build. Its refreshing to see someone sharing their assembly process with such detail.

Now when someone has RB26/30 buld questions they can just come to your thread instead of being flamed for not using the search button (which produces more BS than real useful information).

Do you have a purpose in mind for the car? Drag, street, track or all of the above?

thanks ....

i will keep the updates going ..when i am back in canada..

i am currently traveling around tokyo and HK !

  • 3 weeks later...

more updates !

it's finally looking lik a car now!

with fuel system completed !!!

starting from the back

R0011046.jpg

R0011049.jpg

R0011065.jpg

R0011066.jpg

R0011050.jpg

fuel lines protector guard !

R0011055.jpg

fuel line holder

R0011051.jpg

R0011052.jpg

at the front

R0011068.jpg

dash completed ! glued the back together !

R0011061.jpg

heat sheild for turbo and down pipe

hand made wrap!

R0011039.jpg

R0011041.jpg

R0011070.jpg

R0011071.jpg

HKS to4Z turbo bell mouth machined to fit with my T78 greddy turbo

R0011072.jpg

R0011073.jpg

since the engine is 3inches taller...we made this angle down so i can use my billion rad hose instead of getting soemthing else

R0011045.jpg

polished PS tank

R0011043.jpg

so more work done @ Keep Performance Lab today ~

i must say these guys are so Good with Wires !!!

again keeping it clean is always on the top of the minds. so organizing the wires were very important as it is easier to work on as well as it looks alot nicer.

here are some pictures from today

R0011107.jpg

R0011106.jpg

R0011112.jpg

R0011120.jpg

R0011109.jpg

R0011118.jpg

back of the kill switch mounted where the rear wiper used to be

R0011103.jpg

attention to details

Keep Performance lab even got the Bolts on a OLD HKS coilover GOLD PLATED

R0011125.jpg

my external oil pickup as well as both the external head oil drain and turbo oil drain (had to reuse some old fittings as i don't have time to get new one anodize gold)

R0011123.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Biggest thing is you're okay!   It sounds like between the accident, and the drive home, it was a pretty torturous trip again! On the bright side, you took the opportunity to enjoy the event more from the perspective of a spectator, than as an entrant!   Sad to see so much damage to the car. It really has taken a HUGE hit in the front end. If/when you choose to repair, hopefully the rails are straight (At least from shock tower backwards). Hopefully the extra cage coming through there has save most of the chassis rails, and HOPEFULLY saved the motor too. Best of luck when you eventually get motivated to start pulling it down to check it all out
    • Sounds more like what Brad said, that it's mainly transfer. What pad bed in procedure did you use, and did you replace/machine the rotors, or just swap pads?
    • The stutter is almost entirely in the pedal. I don't feel the brakes release and reapply as you would with ABS engaging but the pedal feels that way, without the brakes releasing. It only lasts for less than a second and the pedal is fine again. It's hard to explain, sorry.  I'll get under this weekend and just double check everything is tight. Fluid is at max where I left it.
    • What bedding in procedure did you use?   When you say stutter, what exactly do you mean? Like it feels like someone letting go of the brakes momentarily and regrabbing them again to get you to stop? Re-reading your post, and that is what it kind of makes me think you're explaining, like theres a little bit of a jolt, likely just as you're reaching a stop. I've only had this issue once. And if its caused by what caused mine, you will want to get the car up on stands again and check it over. Mine was a case of a caliper mounting bolt coming out and letting the caliper rotate on the other remaining bolt and gave play in a wheel as it came to a stop. But not every stop either!
    • Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - then entered a hotlap with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - hopefully the motor and other things are OK but yet to be seen too. There is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it Effort doesnt win you races though     Apparently this is motorsport !  
×
×
  • Create New...