Jump to content
SAU Community

Recommended Posts

gday.

im selling a GT30R top mount setup. details are

GT30R .63 rear housing - turbo is in good condition, seen around 50 to 60 thou ks

Mild steel manifold - 38mm runners

Tial copy external gate

Dump pipe

external gate piping and front pipe all to suit.

so basicly all your gonna need is a intake pipe from your afm to the turbo and oil and water lines to suit the turbo.

SOLDb]

ill get pics up in the next few days, at the moment i cant find any on my computer.

cheers

edit:- sold

Link to comment
https://www.sau.com.au/forums/topic/213561-gt30r-kit-to-suit-r33-sold/
Share on other sites

i cant give you a torque figure but suffice to say there was plenty of it. last dyno it pulled around 250rwkw on standard internals + or - around 10kw for different dynos.

i know the last time i went to a track day i was runnin outta grip at the end of my last session and started puttin it sideways through corners and was easily smoking the tyres,

depending on whether my shares keep going back up, might give you a call late next week, if it's still for sale.

when did this setup hit boost.

looking for something responsive. peak power is not too important.

to me this turbo was a very responsive turbo.

due to the smaller exhaust housing it was quite easy for the rb25 to spool it.

iirc i usually had full boost around 2.5k - 3krpm

its been a long time since i drove it so i cant remember, all i can tell you is that its a very good match up for a rb25 engine

I would love it, but the budget just can't stretch that far at the moment.

going in on wed for a new clutch and boost controller, and then probably fitting a wolf 3d a week later.

depending on how quickly i bounce back from that, you will hopefully be hearing from me



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...