Jump to content
SAU Community

Kit  

22 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

hey all,

i'm selling my car but have a spare genuine uras d1 spec II kit laying around and i was wondering if i should kit it up or sell it as is.

just want some of your opinions.

cheers,

dave

Edited by Advent34

agreed with all those comments above ^^^....dont kit it but sell the car with the option of selling the car with the kit....and if worse comes to worse then sell the car and kit seperately

I think the URAS kit looks nice with some deep dish's. and tastefull mods.

alot of ppl just bang on the uras and dont worry about anything else. I think thats why its got a bad name on here.

i see on alot of cars with the uras kit, the paint doesnt look that great on them because its such a big kit.

sell the car without it on and throw it in at an extra cost. if they dont want it sell it and make abit more money.

this tastefull enough the mods i mean 800ps :cool:

785441_2.jpg

785441_4.jpg

I think the URAS kit looks nice with some deep dish's. and tastefull mods.

alot of ppl just bang on the uras and dont worry about anything else. I think thats why its got a bad name on here.

I prefer to see wheels sitting wider than bodywork.... still looks meh to me no matter how much HP the car has got.

if the wheels were sitting further out then the kit it would look better but not great.

thanks for your replies.

for me, i really like the uras kit, but others may think otherwise.

i was only thinking putting it on if i was to keep the car and wanted some others opinions.

cheers

-dave

if the wheels were sitting further out then the kit it would look better but not great.

What I meant was I dont like a very wide-flare kit full stop (uras, bn etc).

On the car above I would rather see the GTR rims sitting slightly wider than factory bodywork OR a very mild sideskirt to give it a lower stance, not wider. Give the vehicle extra track rather than extra fibreglass... but I guess I havent yet finished a car to my own standards either!! LOL

/end off topic from me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...