Jump to content
SAU Community

Installing An N1 Oil Pump!

r32r32

By r32r32,
in General Maintenance

 Share

Recommended Posts

SECURITY Grand Master

SECURITY

Posted
Posted

you're meant to fill it up with vasoline so as soon as you start the car up its got oil pressure.

before you start the car just leave the cas and injectors unplugged and crank the motor without the spark plugs in. this will build up oil pressure faster. once you've got oil pressure then put it all together and off you go.

Godzilla32 Veteran

Godzilla32

Posted
Posted

N1 oil pumps suck. So for starters i'd throw it out and use the stock one over that. They have layered gearsets which are more prone to cracking from vibration during such things as hitting the rev limit. To answer your question all i suggest to do is use some grease to lubricate the gearset. These pumps have no problem priming so the old vaseline trick isnt necessary. As mentioned remove the spark plugs and unplug the ignition module and wind the engine over until you get good oil pressure then put the plus in and reconnect the ignition module and fire it up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...