Jump to content
SAU Community

Profec B Power Fc

Rav

By Rav,
in Engines & Forced Induction

 Share

Recommended Posts

Rav Proficient

Rav

Posted
Posted

Hi Guys,

Ok Just want some info on hi and low boost tune how does it work,

I have a Power FC and a Profec B, When they tune it on low boost Does it read a diffent map then when it's on hi boost, Because if they tuned it only on one of the settings wouldnt it lean or be to rich and not run as good as it should?

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/214197-profec-b-power-fc/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

well yeah adrian is right, a good tune will make sure its suitable for both

it will just cost you more $ as the tuner will have to spend more time, they'll do it on say low boost

then get it all nice, and then press the high button and see how much has changed etc.

so it will work, just expect to pay a bit more i guess

ask them

paulr33 Grand Master

paulr33

Posted
Posted

not necessarily no, the low boost tune could run across load cells that have too high timing

of course you would see this via the knock warning function and engine check light but its still possible, the afrs could be ratshit too

i dont think it would mattter which order you did it in

evil_weevil Grand Master

evil_weevil

Posted
Posted

ah fair enough!

Ive got the same combo...mine runs sweet but was just seeing what the process could have been!

I get slightly more knock on high boost than low, but still a low knock level :)

Adriano Grand Master

Adriano

Posted
Posted

In reality, a perfect tune on high boost should have a perfect low boost tune in it, but usually doesn't, there is no difference between part throttle high boost, and lower boost(same load cells) I always start with lowest boost, even no boost power runs and datalog it, then slowly increase the boost, tuning each one as i go. Gives optimum power at all boost/load levels

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Recommendation for engine oil funnel spill free

      By MBS206 · Posted

      I thought I'd come back and add something I JUST learned. A Toyota LandCruiser with a 1HZ, mates perfectly with a bottle of Nulon brake fluid. As in, it perfectly screws in. Great make shift funnel when you cut the bottom of it off. This may work for your Corolla.   Unfortunately, tipping a 10L drum is much harder than a 4 to 6L bottle, and they no longer include the easy pour tap which was just perfection to use previously.  
    • EndZee
      Fuel Pump Control Module & Dropping Resistor

      By EndZee · Posted

      Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
    • Duncan
      M35 Brake caliper replacement

      By Duncan · Posted

      You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Duncan
      Most women will agree that parking is the most taxing part of driving

      By Duncan · Posted

      Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Duncan
      Jacks that fit under GTR lips that can reach the subframe?

      By Duncan · Posted

      Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
×
×
  • Create New...