Jump to content
SAU Community

Recommended Posts

Originally posted by JimX

Can you get decent tyres in 255/40/17 size for around or under $300? All of the big brands seem to be $450 each. There must be something almost as good for less.

not quite 255... but for brand.

I've got simex 215's. They handle 190rwkw 'ok'... but they aren't as bad as you'd think.

In the wet, well, can't do much, 215's dont go very far.

But in the dry they are very grippy indeed.

If i go easy on a launch and then hammer it once i get to 3000rpm then i barely wheels spin at all. Very impressed with the grip.

The cost under... $150

so for 235/255 i would think 250/350 wouldn't be far off at the worst.

I've seen other cars using them a bit lately now...

they might be worth a look?

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

i had falken ziex 255/40/17s on my car from japan so dunno what they were worth, but they didnt really grip much, espcially when they started to wear. since my car is low, but not really low, the inner tread wears a lot faster because of the neg camber. when i replaced them, the inner tread was almost smooth and the outer tread was still 95% ;). in the dry in a straight line they just used to spin in 1st and all through 2nd, and my car is almost stock.

i still have the falkens on the front (235s), and they are fine for front tyres, no problems at all.

i recently purchased Dunlop FM901's 255/40/17 for the rear, $310ea fitted/bal. they are only really just wearing in now, theyve only done a couple of thousand kms. they havent spun once in the dry, and grip like hell in the wet too, i highly recommend these tyres if you can find some for a decent price.

Ended up going for a Sumitomo as i have heard only good things, soon will see $220 each unfitted 255/45/17. Would love the Ggrid II's but not available in Aus.

Brig S-03's are $430 a pop and gone by 20 thousand. Wouldn't mind looking into the Bridgstone RE 540 but dont think the size is compatable?

Hi,

Hey Roy13,

You mentioned you want Brigestone Grid II's..

I have them... I find them to be shit... (255x40x17).. They have to be really warm for them to operate well and even then I find it very easy to spin them...

Phantom,

Very interested to see the result of what is out on the market for around $300 each..

Rob

Originally posted by Phantom

i goin 265/35/18 now and i dont even wanna think how much they gona cost me.

Originally posted by JimX

Can you get decent tyres in 255/40/17 size for around or under $300? All of the big brands seem to be $450 each. There must be something almost as good for less.

I'm in the market for new tyres and I've found that Hankook seem to be the best value for money going round. I went into a tyre place asking for 255/35/18 Bridgestone S02s (@ ~$600ea) for the rear and was told that the Hankook K104 sport (265/35/18) out-performs them (many other tyre outlets have also backed this up). The best part was the Hankooks were $330ea!! A silica compound at that price impresses me :uh-huh: .

For anyone that's interested - I got prices for all 3 Falkens listed on their site.

The ST-115's are $289 each, and both the FK-451's and ZE-326's are $310 each. These were all in the size of 255/40/17.

I will be getting the 451's I think, I've got silica tyres on my motorcycle and I love them.

big call to say all tyres from a brand suck. have you ever tried their azenis? Have you done a lap of Eastern Creek in under 1.57 in your stock skyline on those tyres you say are better?

I totally agree that the z326s suck, they were on my car for compliance and were terrible, in fact I'm surprised that JimX was quoted the same price as for 451s.

Im happy with the 451s for both wet and dry performance.

Originally posted by Duncan

I totally agree that the z326s suck, they were on my car for compliance and were terrible, in fact I'm surprised that JimX was quoted the same price as for 451s.

Duncan, are you sure you're not confusing the ZE-326's with the ZE-502's? The latter are much cheaper I think. That's what Ben had on his for compliance (by the dealer) and I'm pretty sure they weren't an overly expensive tyre. They usually throw the cheapest tyres on they can find for compliance. Of course I could be wrong, maybe you got the number right and they do suck :P It's just that I know that the 502's are really bad.

on my rears i got a nankang ZIEX and a falken ZIEX? both are identical in tread, stiffness and dimensions.

i was under the impression that nankang was an asian branch of falken?

i find that they dont offer that much traction e.g. alot of wheelspin on launches, but i find that they work quite effectively in wet, although i am comparing their wet weather performance to thinner tyres, so might not be a fair assumption.

Thinner tyres will generally handle better in the wet (all other things being equal) because they can push the water out of the way a lot easier. That's why some fat wet weather tyres have HUGE vertical grooves in them, to try making them the equivalent of 2 smaller tyres.

So it's fair to compare a thicker tyre with a thinner one in wet weather. If anything the thicker one is at a disadvantage.

  • 1 month later...
Originally posted by Sumo

What do you guys think of Wan Li tyres? I can get the fitted for $175 for a 235/45/17 and was thinking about putting them on my steer.

I'd be reticient to put shithouse tyres on the front.

On the back, yeah because you guys are just gunna burn them up anyway.

I ended up with shithouse 245/45/17 at the rears for $155??? Hankook silica? Not too good IMO but I had two nails in the back so...

I'm after a set of 255/40/17 but I think I'll end up with Nankang NK2 as they seem to get high marks from the D1 teams (for the wrong reason I would imagine).

T.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...