Jump to content
SAU Community

Recommended Posts

Originally posted by haste

Does anyone know where to get a road worthy, even though the car has a relatively sizeable top mount turbo? Need to get the car registered.

i just got my car rw and rego'd with top mount but then a mate went to same rw place a week later and they wont do it. still hasnt found anyone to do it. its all luck.

RW testers are liable in court if you or someone else is hurt ,or in any accident if the car is found to be un road worthy. Accident insurance apraisers do check.  

It is more difficult now

Thing is though, you took the vehicle there, they tested it.. a week later 50 mods are back on after you left it with your "brother" there isn't much they can do.

Anyway, with the big top-mount turbo thing, you should be able to get it engineered for under $1000, then its fully roadworthy and can be registered that way. Probably the best way to go about it. It is possible to be fully legal you know, it just takes a bit of $

Get it done properly. (Eng cert, etc)

Think about, if you can get a RWC for a car that obviously isn't, then what does that say about RWC when you go sell/buy a car?

If there is one standard that EVERYONE sticks to, then everyone knows what a RWC means. Otherwise, you might as well sell your car with the 7 of clubs cuz that is as bout as meaningless as a RWC.

i spoke to an engineer about getting my car engineered so that its all legit. he told me that you cant get a car engineered that has been modified that is newer than the 80's (?) and he said that the only way to do it was to get it checked by the epa which cost 4k. dont know if this is ture though.

No, its not actually true.. but some places probably are either unfamiliar with how to do it, or can't be bothered.

Getting it certified for EPA pollution regs is again a different matter..and yup, i think its a few $k because it has to go through a full involved process

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...