Jump to content
SAU Community

Recommended Posts

  • 1 month later...
Just need some coilovers... then mines not too bad :P Also waiting for my GTR spoiler to get painted and fitted.

08_26_1.jpg

More pics can be found here

Looks nice.. Your car is virtually the same as mine now - Same front bar, skirts, same coloured wheels.. Same mods and then me waiting on coils/springs too lol

Cheers Greg,

After a bit of research i learned it was a full top secret kit minus the front quarters with the vents. Its now got Tein Super Street Coilovers, Carbon Intake Pipe, Jim Wolf Popcharger and heatshield, Stainless Extractors and Johnny Spec Twin 2 1/2" mandrel bent zorst with highflow cats and x pipe.

Unfortunately Some lovely fu(k keyed it last week so its booked into the body shop to get the entire passenger side and front bar resprayed... Was so close to having a enough money to order some 20's for it and now this... iggnorant pricks... ah well... ill post some more pics tonight

hey thanks Greg

she is definatly starting to look good................now to make her go a bit faster........gonna be doing some engine work next year aiming to (hopefully) get close on 200 kW at the wheels

with no turbo, supercharger or nos :(

Heres a couple more, looking at some dress 20's for it but next mod will be a kazz 2 way.

Believe it or not were considering a VK56 swap for it... same reason we did blacky originally, the current engine/gearbox combo is worth alot of money here in aus, id import the titan engine and another vq 6 speed manual and adapt it... just researching atm... but its looking good ;)

post-3649-1188461561_thumb.jpg

post-3649-1188461575_thumb.jpg

post-3649-1188461588_thumb.jpg

Hehe yeah.. I ran a 14.32@98MPH with all the mods but with the stock airbox... Pretty sure its quicker with the stock airbox over the pod... But for the time being the pod stays as it gets rid of some of the horrid twin cam resonance it has, putting some extra resonators and expansion chambers in the exhaust over the weekend to hopefully fix that. Its plenty quick enough, but it would just be damn cool a V8, especially the VK56.

ill have to get some 560GT badges made up just to confuse people if and or when i do it :)

marios r33 is f**ken shhhmick! +10 votes for you

i love the white r33's even if there are alot of them around, my old stacked 33 was white my new one is grey....i like white better =/

where did you get your interior done? could you post some more pics of the interior? cheers

  • 2 weeks later...
marios r33 is f**ken shhhmick! +10 votes for you

i love the white r33's even if there are alot of them around, my old stacked 33 was white my new one is grey....i like white better =/

where did you get your interior done? could you post some more pics of the interior? cheers

thanks man, at least i got a fan haha

ive changed the car a fair bit thou, lowered it more, added the rest of the kit etc, looking shmick

a mate in sydney dun it

im tryin to sell the interior now so hopeing sumone buys its

i will get sum shots up of the trim thou

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...