Jump to content
SAU Community

Recommended Posts

Hey man

I have just installed about two months ago a 3076r. i got 271rwkw at 17psi

your 600cc injector might max out at 270rwkw man

you might need bigger injectors or a fuel pressure reg

i have 740cc injector and there at 80% cycle

My clutch had the dick at 270rwkw also

i just bought a Os giken twin plate too.

As for coils. Man you need them as then will miss fire hard

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey man

I have just installed about two months ago a 3076r. i got 271rwkw at 17psi

your 600cc injector might max out at 270rwkw man

you might need bigger injectors or a fuel pressure reg

i have 740cc injector and there at 80% cycle

My clutch had the dick at 270rwkw also

i just bought a Os giken twin plate too.

As for coils. Man you need them as then will miss fire hard

Get your car checked.

I am making 274rwkw @ 15psi on a rb30det, using 550cc and my duty cycle only reaches 72% MAX.

Wow boys nice replies.....................

With those injectors is there a Fuel presusure reg involved..........

I am using 740cc but my fpr isnt really in use ............

My turned name is Dave formally know as Dyno Dave. been tuning for over 20yrs

i believe he has some experiance

Charlie, without trying to start a shit fight or start throwing insults around, please confirm your injector size (don't just tell me they are 740's, take the number 1 plug off and confirm the colour, i'm assuming they are nismo's), the fpr base pressure and the fuel pump and wiring being used. 740's should be capable of a lot more if the rest of the fuel system is up to scratch.

Don't start claiming dave is the greatest tuner ever and what he tells you is gospel. Your results are significantly different to other results so find out why. Do not accept what one guy tells you. Either the dyno is reading low (which i know bel's doesn't) or there is some other issue.

Book in a run with UAS, CRD, Unigroup, JEM, whoever and get a second opinion.

I don't want to labour on duty cycles either, so can you post up the sheet on the result here?

270kW @ ~17psi with a 3076 on an RB25 is fairly typical, and a good stout result.

I saw from one of your posts that you are running an external gate. What manifold is it all bolted to?

I have just installed about two months ago a 3076r. i got 271rwkw at 17psi
Wow boys nice replies.....................

With those injectors is there a Fuel presusure reg involved..........

I am using 740cc but my fpr isnt really in use ............

My turned name is Dave formally know as Dyno Dave. been tuning for over 20yrs

i believe he has some experiance

:cheers:

Well hell in that case you may as well go and buy some 1500cc injectors so your "experienced" tuner can make 340rwkw @ 79% duty cycle. :)

No one questioned the abilities of your tuner, they are saying that something else may be causing your injectors to run harder; but a good tuner would know that 740cc injectors are good for 400+rwkw, so he should be looking at why your setup requires such a high duty cycle.

I do have an adjustable fpr, but it's currently running std pressure. Once my new engine is run-in, i intend to run more boost and hopefully crack into the 300+rwkw range. It is at this time i plan to see if i could get away with adjusting the fpr; If not i could always buy yours for a very cheap price ;)

Charlie, without trying to start a shit fight or start throwing insults around, please confirm your injector size (don't just tell me they are 740's, take the number 1 plug off and confirm the colour, i'm assuming they are nismo's), the fpr base pressure and the fuel pump and wiring being used. 740's should be capable of a lot more if the rest of the fuel system is up to scratch.

Don't start claiming dave is the greatest tuner ever and what he tells you is gospel. Your results are significantly different to other results so find out why. Do not accept what one guy tells you. Either the dyno is reading low (which i know bel's doesn't) or there is some other issue.

Book in a run with UAS, CRD, Unigroup, JEM, whoever and get a second opinion.

That is fair enough.. it is ok not shit fight is starting

I am not saying dave is the best tuner ever

but 20 years experience ..... he must know more than a bit dont you reckon

I have Nismo 740cc (red)

i also have a Sards Fuel reg

Walbro fuel pump

They are capable of doin more.... well except for the fuel pump

I don't want to labour on duty cycles either, so can you post up the sheet on the result here?

270kW @ ~17psi with a 3076 on an RB25 is fairly typical, and a good stout result.

I saw from one of your posts that you are running an external gate. What manifold is it all bolted to?

Im have a tial wastgate gate off the standard manifold

and i get 17psi at 3500rpm

:(

Well hell in that case you may as well go and buy some 1500cc injectors so your "experienced" tuner can make 340rwkw @ 79% duty cycle. :P

No one questioned the abilities of your tuner, they are saying that something else may be causing your injectors to run harder; but a good tuner would know that 740cc injectors are good for 400+rwkw, so he should be looking at why your setup requires such a high duty cycle.

I do have an adjustable fpr, but it's currently running std pressure. Once my new engine is run-in, i intend to run more boost and hopefully crack into the 300+rwkw range. It is at this time i plan to see if i could get away with adjusting the fpr; If not i could always buy yours for a very cheap price :)

Ill get my sheets on the comp and ill post them up asap....

That is fair enough.. it is ok not shit fight is starting

I am not saying dave is the best tuner ever

but 20 years experience ..... he must know more than a bit dont you reckon

I have Nismo 740cc (red)

i also have a Sards Fuel reg

Walbro fuel pump

They are capable of doin more.... well except for the fuel pump

Im willing to bet it is your pump and not your injectors i got my car tuned and it showed up around 80% duty cycle with 600cc injectors and was making only 245rwkw with 14psi...changed the pump, finished the tune and it showed 306 rwkw at 18psi and the duty cycle went back down to high 60s

On to the turbo I had a 3076r with a .82 IW rear made 306rwkw at 18psi and 260rwkw at 14psi it was quite responsive though i did have poncams to help, all up it was a nice linear turbo on the street not so much down low that it would wheel spin all over the place and not too laggy

Im willing to bet it is your pump and not your injectors i got my car tuned and it showed up around 80% duty cycle with 600cc injectors and was making only 245rwkw with 14psi...changed the pump, finished the tune and it showed 306 rwkw at 18psi and the duty cycle went back down to high 60s

On to the turbo I had a 3076r with a .82 IW rear made 306rwkw at 18psi and 260rwkw at 14psi it was quite responsive though i did have poncams to help, all up it was a nice linear turbo on the street not so much down low that it would wheel spin all over the place and not too laggy

hey mate,

Your 3076 was internally gated? Where did u source it from if u dont mind me asking?

:whistling:

hey mate,

Your 3076 was internally gated? Where did u source it from if u dont mind me asking?

:whistling:

I got my internally gated GT3076R through Slide on these forums.

Here is his new thread, i just happened to see: Slide's Garrett Turbos

hey mate,

Your 3076 was internally gated? Where did u source it from if u dont mind me asking?

:D

I got mine from this man here Elite Racing he was a few hundred dollars less than Slide at the time but i would get a prive from both.

What did you do about water and oil lines? also did it require a spacer plate?

How have you found the internal gate? No boost creep at the higher end? :thumbsup::D

Sorry for all the question!

Cheers mate

water and oil lines can be ordered from the above two guys it did require a small spacer, mine fitted on the manifold...but only by about 1mm so we thought it was best to space it out a little lol. I had a 14psi actuator I had no boost creep at all but if you had a lesser actuator I think you may strike the odd problem

That is fair enough.. it is ok not shit fight is starting

I am not saying dave is the best tuner ever

but 20 years experience ..... he must know more than a bit dont you reckon

I have Nismo 740cc (red)

i also have a Sards Fuel reg

Walbro fuel pump

They are capable of doin more.... well except for the fuel pump

why hasnt your experienced tuner told you that your running out of fuel! and recomended you change pumps?

as i suspected your running a walbro, which is a awesome pump for early stage 1 mods, but once past 250rwkws the walbro run's out of puff. change it soon if you like your bottom end.

why hasnt your experienced tuner told you that your running out of fuel! and recomended you change pumps?

as i suspected your running a walbro, which is a awesome pump for early stage 1 mods, but once past 250rwkws the walbro run's out of puff. change it soon if you like your bottom end.

Good pick-up

+1 to replace walbro pump.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
×
×
  • Create New...