Jump to content
SAU Community

R32 With R34 Front End Conversion?

catchmydriftr32
 Share

Recommended Posts

BANGN Experienced

BANGN

Posted
Posted

i think it looks like shit.. not just that i beleive that there is a modification to the front end in order to get the right "caster look" so you dont have a big gap in the front of the wheel, i read somewhere a guy either extended the front or brought it back i couldnt remember but still I say dick that and go 32GTR look

Spunky Munky Grand Master

Spunky Munky

Posted
Posted
i know what you mean, with the front end almost seeming 'bigger' than the rear in the 32/4 convert

BUT.... if you go full wide-body on the R32... then it'll be sex on wheels... Ilove the R32 sides - but just not fat enough for the massuve R34 front (that's why the R33 does better here stock for stock) so if you go PHAT... it will be mind blowing... you're going all out - might as well wait a bit longer or spend a tad more and perhaps go ALL OUT? :thumbsup:

jackdanielz Collaborator

jackdanielz

Posted
Posted

well just lettin u guys kno,

if anyone ere wants to have my R34 for front end, id be taking it off soon hopefully...

if everything goes in the right way,am thinking in getting my money all set in 2 months time or prob 2 weeks if u guys give me a good offer!! :ermm:

business!business! :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • sonicii
      Anyone running the VQ37VHR with forced induction?

      By sonicii · Posted

      I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Fuark, at least the motor survived. What brand was the fitting that snapped?
    • GTSBoy
      Anyone running the VQ37VHR with forced induction?

      By GTSBoy · Posted

      Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • GTSBoy
      Starter motor replacment teeth count.

      By GTSBoy · Posted

      Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...