Jump to content
SAU Community

Recommended Posts

The 60 is when the oil is cold and you want your oil to be think on cold start to protect the engine from wear. is more the smaller number that is inportant because that is the thickness when hot which is what your engine spends most of it's time being. If you look at what nissan suggests for our climate and they recomend 10W-30/40/50. For 5W-?? the climate they suggest for this is around 10 degree max. If i was on my computer i could post the chart up from the manual, i can do it later if people are interested.

Edited by D_stirls
The 60 is when the oil is cold and you want your oil to be think on cold start to protect the engine from wear. is more the smaller number that is inportant because that is the thickness when hot which is what your engine spends most of it's time being. If you look at what nissan suggests for our climate and they recomend 10W-30/40/50. For 5W-?? the climate they suggest for this is around 10 degree max. If i was on my computer i could post the chart up from the manual, i can do it later if people are interested.

I think you have that totally backwards.

The lower number is how the oil acts when cold (in the case of a 10-60 weight oil the oil acts as if it is a 10 weight oil (thin) when cold.

The higher number "60" reacts the same as a 60 weight oil (thick) when hot.

All engine oils get thinner when hot, so the oil will not be physically thicker when hot.

When cold you need a light oil to move from the sump to all the parts that need the oil to lubricate. In a freezing temperature climate ie Canberra in Winter 5w engine oils assist in starting the car and limiting engine wear.

Most of the engine wear on a normal car occurs at startup where there is limited lubrication.

Better re-read that chart.

I think you have that totally backwards.

The lower number is how the oil acts when cold (in the case of a 10-60 weight oil the oil acts as if it is a 10 weight oil (thin) when cold.

The higher number "60" reacts the same as a 60 weight oil (thick) when hot.

All engine oils get thinner when hot, so the oil will not be physically thicker when hot.

When cold you need a light oil to move from the sump to all the parts that need the oil to lubricate. In a freezing temperature climate ie Canberra in Winter 5w engine oils assist in starting the car and limiting engine wear.

Most of the engine wear on a normal car occurs at startup where there is limited lubrication.

Better re-read that chart.

Yep sorry i have the numbers around the wrong way;

But here's the chart;

post-27020-1209911315_thumb.jpg

The 10 or 10W is not a viscosity its a cold pouring index . So 20w50 is not 20 weight oil when its cold .

Synthetic oil is supposed to be quite "thin" when it's cold like very cold and this would be a huge advantage at start up .

Plenty of people like the Edge 10w60 but if the 60 number scares you Mobil do a synthetic 15w50 from memory .

If I was pushing a turbo engine hard and for any length of time I'd use the 10w60 too .

A .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...