Jump to content
SAU Community

Recommended Posts

1 question i have that im gona send an email away is if i get the v88 and i get it tuned for the neo motor and i put a different motor in like a 26 can i load a 26 map into it later and tune that or i have to get another ecu.

  • Replies 895
  • Created
  • Last Reply

Top Posters In This Topic

can anyone confirm that the v44 plugin will run low impedence injectors without using a resistor pack?

I have heard they from different people that they will but have also read you need a resistor pack.

Anyone done this yet?

Vipec V44 plug-in manual:

GTR models are fitted with LOW impedance injectors run via factory fitted ballast resistors. This ECU has been designed to be used with HIGH impedance (greater than 6 Ohms) injectors. Ballast resistors must be wired if low impedance injectors are to be used. This means that the ECU is plug-in compatible with factory fitted injector/ballast combinations on all models.

with the amp or with the figures in the knock map?

with the amp. i'm keen to know how people are setting up the knock response threshold since it's hard to know what knock sounds like for a given engine unless you can produce it. ie no point having the knock function set at a threshold such that the thing is rattling away but the ecu does nothing because the knock severity at which it acts only occurs when the conrod exits the block.

unless of course it's a noise filter like the Turbo XS Knocklight.

would also be nice if they could find a way to use the standard knock sensors on the GTR.

with the amp. i'm keen to know how people are setting up the knock response threshold since it's hard to know what knock sounds like for a given engine unless you can produce it. ie no point having the knock function set at a threshold such that the thing is rattling away but the ecu does nothing because the knock severity at which it acts only occurs when the conrod exits the block.

unless of course it's a noise filter like the Turbo XS Knocklight.

would also be nice if they could find a way to use the standard knock sensors on the GTR.

it uses the standard sensors, the plugin and the V44 need an amp/signal filter so that the input is 0-5v without much random signal noise where as the V88 has that built into the unit.

Scooby....

Ear muffs/det cans. :geek:

i know how you listen for knock, what i'm asking is how you set the knock correction point if you don't know what knock freqs are for a given engine.

if it was standard practice to get the engine to 'just' start knocking and set that as the threshold for the ecu to trigger knock control there would be no question, i just don't intend getting my car tuned that way.

Turbo XS claim that once the procedure of calibrating the Knocklight to the freq range of normal engine noise for a given engine - ie without knock - is complete, it recognises freqs outside that as knock. they are confident that the unit will pick it up correctly because knock freqs are fairly unique. in other words it detects freqs outside those parameters as knock, although the suggestion is that knock freq range is extremely narrow. i'm not advocating their approach but i can see it's plausible as they use the parameters of an particular engine's unique freqs.

another example; the stock GTR ecu has knock control but if you use it on an RB26/30, which will have a different knock freq to a stock RB26, there is no guarantee it will be effective as what it hears when a 26/30 knocks itself to death might be different to what it has been calibrated to recognise as knock.

hope that makes sense.

just not sure how it's done with the Vipec.

Edited by Scooby

With the vipec can you select high or low impedance injectors?

Also just wondering considering the current group buy on the Haltech E11V2 @ $1545

Why would you choose the Vi-pec over the Haltech?

Those who have the v44 whats your idle like? Now I have the injectors and hks turbo on, the idle seems to hunt a lot, where before it was almost flat as a tack? Is it worth doing some data logging?

Those who have the v44 whats your idle like? Now I have the injectors and hks turbo on, the idle seems to hunt a lot, where before it was almost flat as a tack? Is it worth doing some data logging?

your engine didnt eat turbo bits did it?...probably only a simple air leak though...are the injectors sealed where they seat on the head flange?

your engine didnt eat turbo bits did it?...probably only a simple air leak though...are the injectors sealed where they seat on the head flange?

My engine may of eaten some small turbo bits, compression test came back regular no cylinder vastly different to the other., some small metal flakes were found around the intake and around the IM. Intercooler piping etc was all cleaned out. What do you mean by are the injectors sealed?

Wasn't doing this for the few mins I had the car idling after the turbo blew.That was with the old injectors

thx

My engine may of eaten some small turbo bits, compression test came back regular, some small metal flakes were found around the intake and around the IM. Intercooler piping etc was all cleaned out. What do you mean by are the injectors sealed?

thx

they have small rubber insulators that seal the injectors to the head...its quite common to not seat them correctly allowing a small amount of air to enter the system which is making the idle hunt.

Frankly I wouldn't know, I have the software to monitor the ecu, but I havent had the chance to use it.

edit: I'll have a look tomorrow to see what I can around the injectors, thx for the tip.

Will see if I can do some datalogging of the ecu on friday as well.

thx

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
    • Oh and some up-and-comings; New rear drivers wheel bearing. I'll do that this weekend while the diff is out. The car is already up and the d/c axles and missing exhaust will help with space. This is the last bearing for me to do and I've been dragging my feet on it. I also have some new EBC blue stuff pads for the car and some new brake fluid. I haven't ever flushed the fluid in this car and looking forward to it. I have 600 degree fluid to put in. Not exactly "race fluid" but better than the typical stuff I have been using.
    • A proper clutch/plate type mechanical diff with quite a lot of pre-load and high locking % is better for drifting. Much more consistent in its behaviour. A helical can be annoyingly vague and inconsistent in how it responds under the sorts of abuse found in drifting.
    • Some updates here. I pulled the entire interior out, minus some trim to respray the seats with Colourlock dye. It turned out really nice though I accidentally let the dog in the car after and she scratched up the front seat.  This is what it looked like before, the colour was just washing out everywhere but thankfully the leather was in good nic. Then after the respray   And after the bloody dog jumped in The headliner is out waiting to be retrimmed, but it will stay out now until Nov - see why below. I replaced the stereo/headunit with a period-styled Android headunit. I have no after pics, but I'll get some. This is because of the missing pixels. I tried to fix this twice with replacement ribbon cables but couldn't. Also the bluetooth interface I'd bought for this was crap. Then there's the rusty roof. Pics and info in this other thread. I have decided to get this repaired professionally, but I'll update that thread. This is why the headliner will stay out for now. I'll be getting the roof and bonnet resprayed at the same time the rust is fixed. I also had an interesting issue with my drivers door lock.  For a small period I was having issues getting any 12v power to the car - I mean *any*. It would have no dash lights, nothing. It happened while I was at the shops and I couldn't get in the car. So, we had 2 problems. The most pressing here is that I was locked out. I have only a single physical key hole on the car, the drivers door and no amount of turning would unlock the car. Surely it doesn't need power for this? The second issue is why am I losing all power periodically, The battery isn't dead, its almost like the battery isn't even there. Two issues that were surprisingly easy to fix. You fellow BMW over-engineering lovers will appreciate this. The lock in the door has 5 states; mechanical lock, electric lock, neutral, electric unlock, mechanical unlock achieved at -90 degrees, -45 degrees, 0 degrees, 45 degrees and 90 degrees. Although, the unlock is towards the front of the car, so opposite for LHD countries. Sticking the key in and turning 45 left or right is what is used 99% of the time. It activates the central locking etc. 90 degrees is for dead battery access and, obvs, only un/locks the one door. But because the mechanical lock is never used and is 27 years old, it seizes up. I was totally unable to turn the key far enough to get to the mechanical unlock (At the time of locking myself out, I didn't even know this was a thing). I eventually did it with some vicegrips and teflon spray.  I made a quick vid for other E39 peeps.   The battery issue is totally new to me also - It wasn't making sufficient contact between the post and the terminal. The terminal was bolted on tight, but the car wouldn't have power. After checking the battery with my multimeter I accidentally contacted the terminal and the battery post and the car got power. The battery was only a few years old and in good condition. I cleaned the post and the terminal with a wire brush, bolted it back on tight and never had the issue again. I'm still surprised that despite having solid contact it didn't work. Also, the car was getting Warragamba sized pools of water in the back when it rained. My initial concern was another rust problem. But when I went out on Weds while it was raining and while I had no headliner in I could see a steady stream of water coming through the roof mounted aerial. As this aerial is for the (now removed) car phone I pulled it out and whacked a blanking grommet in the hole. It seems fine now. I'm thinking I might get the hole permanently filled when the rust is fixed. Moving forward and things in progress; The tailgate needs some attention. I have taken all the trim off to clean it all and address some small rust spots. I have partially done all of this but I'll finish it up hopefully this weekend. As all the trim are now entirely devoid of trim clips I have bought a heap of strong velcro and I'm hoping it does a good enough job as any of this trim in good condition is super expensive and usually in Europe as we dont have many of the wagons here. Suspension and brakes!!! This is exciting. In the front; New control arms New sway bar links New lower Eibach springs (the only modification I'm planning on this car) M Sport shocks (these came with the car and will replace the longer shocks in the car) New top mounts Used 540i calipers (stock brakes suck!) New 540i disks and pads (22x296 mm for 528 and 30x334 mm for 540i) New front wheel bearings (thank all that is holy for bolt on bearings!) Annnnd in the back; New control arms New sway bar links Adjustable air suspension arms (fool the car into what the current height is so the self levelling suspension can match the new front ride height) New ball joints I'll also be doing a brake fluid flush while I'm in there. I'm planning on switching the car over to the 16's that came with it so I can clean up and respray the M Sport 17's. They've lost a lot of colour over the years and have some gutter rash. None of this will start until the E90 is back.
    • You mean you will regret it for drifting duties? I don't quite follow.
×
×
  • Create New...