Jump to content
SAU Community

Recommended Posts

Wrecking TWO R33 GTSt's, both series 1s, popular parts listed but all parts avaliable, for anything not listed PM me :)

Engine (RB25 turbo): $1800 each

Transmisson: $500 each

Custom Leather Interior: $800 for Front & Rear Seats

Series 1 Interior: $400 Front & Rear Seats

R33 GTR Wheels: $1500 set with brand new rubber

Aftermarket 5 Spoke Alloys: $700 set with tyres

R33 Type M Brakes: $400 set

G4 Coil Overs: $800 set

Door Shell: $200 each, no trim no window

Boot with Spoiler: $200 each

Tail Lights (pair): $150

Standard Rear Bar: $100 each

Dash Surround: $100 each

Leather Dash: $250 each

Cluster: $150 each

Lower Control Arms: $150 each

Upper Control Arms: $50 each

Quater Glass: $100 each

Factory Side Skirts: $250 set painted black

Factroy Rear Pods: $100 set painted black

Blitz Exhaust: $500, near new

Blitz Dump/Down Pipe: $150

Factory Car matts: $100

Parts4sale1.jpg

Parts4sale2.jpg

Parts4sale3.jpg

Parts4sale4.jpg

Parts4sale5.jpg

~Ferah

Link to comment
https://www.sau.com.au/forums/topic/218549-wrecking-two-r33-gtsts/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I have a mate who needs a shell. Is either one of them any good to use? Damage looks to be minimal.

Not concerned about vins or rego or compliance (racing)

Could you please PM me details.

Is the interior reel or fake leather???

Looks like the ones off the group buy and ebay...

Dnt no lol

I have a mate who needs a shell. Is either one of them any good to use? Damage looks to be minimal.

Not concerned about vins or rego or compliance (racing)

Could you please PM me details.

yea both are fine if ur after shells, both have front on accidents u will need to repair tho.

Ferah,

Probably best thing to do is for me to come around your place and pick out the parts I need and we'll work out a price?

Can you please PM me your contact details and address and I'll drop by...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...