Jump to content
SAU Community

Recommended Posts

Have had this thing sitting around for a few years now, only realised due to a recent clean out.

Was originally sold at $650 but realised that it was not a perfect fit for the car, so refunded customer. So PLEASE NOTE, minor fitting / adjustment is required. However, this is par for the course with so many aftermarket bodykits you'll buy nowadays. Unless you buy a genuine (expensive) Jap product, alterations are not that uncommon, and at least you can check it out here in Hobart.

Asking $350 for the whole thing - front, sides and rear.

If interested, PM me here. I can probably arrange fitting and spraying if required too.

Link to comment
https://www.sau.com.au/forums/topic/218715-r33-gtst-gtr-bodykit/
Share on other sites

  • 4 weeks later...
R33 GTR; Factory items

Original GTR Boot $150

AND

GTR Wing - GOOD CON $350

Also

Another R33 GTR wing, slight damage. make and offer $150

R33 GTS-T Side skirts - GOOD CON - $180

R33 GTS-T Nismo Rear POD's - VGC - $120

Have you got any R33 Gtr front lips?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...