Jump to content
SAU Community

Please Help! Oil Pressure Almost At Zero!

Ki_spirit

By Ki_spirit,
in General Maintenance

 Share

Recommended Posts

Ki_spirit Contributor

Ki_spirit

Posted
Posted

Please help!

After driving my car tonight, I have come home to find my oil gauge reading almost zero at idle! :P

I was driving, stepping on the pedal quite generously and at mid range rpm, the oil pressure is just below the last mark on the gauge!

There appears to be no leaks, although the wastegate of my turbo seems to stutter slightly under full boost repetitively, while being heavy on the pedal.

When cold the gauge can read close to the 4kg/cm2 line but once when warmed up goes down very low!

Please help!! Anyone! I will be ever so greatful for any help!

GeeTR Grand Master

GeeTR

Posted
Posted (edited)

Borrow / see mechanic for a mech o.pressure gauge & test as soon as possible to be safe imo.

As Anna's said, the sender / gauge are awful. Replace sender with a known good one, then purchase a new one if the stocker ends up being bad. If issue still exists, then its most likely your gauge.

Incidentally theres a second o.pressure sender that flash's a red LED on the stock gauge. It'll illuminate at very low pressures.

Edited by GeeTR
blind_elk Grand Master

blind_elk

Posted
Posted

How old is the oil? What type is it (mineral / synth)? What grade?

When the oil gets hot, such as after spirited driving as you have done, it becomes "thinner", and can't hold the same pressure at idle.

Absolute pressure is not as important as consistent pressure.

rb2240sx Newbie

rb2240sx

Posted
Posted

I say check it with a an actual oil pressure gauge. If its still low then change your oil to something heavier until you can find the cause. If I remember correctly, there is a bolt on the bottom side of the oil pump that houses the oil pressure relief valve and spring. You can pull the spring out, stretch it out a bit longer, and reistall. Of course, a clogged oil filter could also be the coulprit. Whens the last time you changed the oil/filter?

nuclear_skyline Mentor

nuclear_skyline

Posted
Posted

IS the engine making any funny noises? No knocks or clacking???

Oil pressure can drop really quick, be just maybe OK when driving, but have bugger all pressure at idle when nasty things happen t your main bearings, like spinning them.... Been there done that...

Silver_R34_GT-T Grand Master

Silver_R34_GT-T

Posted
Posted

my R34 is doing the same thing. i mentioned it ot hte mechanic when getting a service, he said it was all fine, got the brand new oil in it, and my guage reads teh same :D

guess mine is faulty

nuclear_skyline Mentor

nuclear_skyline

Posted
Posted

you can pick up a half decent autometer guage for round 150.... or a cheap working one for under 50..... may not be nice, but certainly will give u peace of mind

Ki_spirit Contributor

Ki_spirit

Posted
  • Author
Posted

Hi guys,

Thanks for all of your replies.

The gauge seems to operate okay, and I have found when starting cold the the pressure is halfway between 4 and 8 on startup - I will look into the sender.

My sump although is still half full and I can see no indications of leaks...

The engine is getting slightly louder though, like the injectors and it is only recently that this has started to occur.

I have no idea what oil is in it, because the previous owner put it in. I am guessing from what he said it would be geting near 3000kms- guessing mineral, no idea on grade :) ; but I am going to change the oil ASAP (will have to look up what is in the book for the spec I guess).

Any recommendations? 185 XXX km's on car.

Am going to flush the radiator and refill as well.

:D

Thanks everyone (kuma j, msnismo, GeeTR, blind_elk, rb2240sx, nuclear_skyline, Silver_R34_GT-T) for all of your help :O

blind_elk Grand Master

blind_elk

Posted
Posted

Depends on the oil and the condition of the engine.

My RB25DET sits around the '4' mark (? , 1st line up) when everything's good (ie correct oil level in sump) and engine up to operating temp. I'm using Mobil 1 15W50 in an engine rebuilt about 10k ago.

As I said earlier, it doesn't matter what the reading is so much as it's stable.

Bliksem Veteran

Bliksem

Posted
Posted

First thing I'd do is change the oil, that is just good practice since you've only recently bought the car.

It's also possible that there could be a small amount of oil contamination which affects the viscocity of the oil ie: small amounts of petrol escaping past the piston rings and making its way into your oil.

Once you've changed the oil (which imo you should do regardless), and if the problem still persists - get another gauge to test the real pressure. As others have said the oil pressure sender is known to be faulty.

nuclear_skyline Mentor

nuclear_skyline

Posted
Posted

Heres a gooden I learnt... When you drop the oil out, make sure the pan is clean before hand and let the oil run into it...

Dont let it sit for too long and run a magnet through the oil to check for metal in it... If your engines getting louder, and your oil pressure is dropping off, could be a bearing issue...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...