Jump to content
SAU Community

Recommended Posts

Please help!

After driving my car tonight, I have come home to find my oil gauge reading almost zero at idle! :P

I was driving, stepping on the pedal quite generously and at mid range rpm, the oil pressure is just below the last mark on the gauge!

There appears to be no leaks, although the wastegate of my turbo seems to stutter slightly under full boost repetitively, while being heavy on the pedal.

When cold the gauge can read close to the 4kg/cm2 line but once when warmed up goes down very low!

Please help!! Anyone! I will be ever so greatful for any help!

Borrow / see mechanic for a mech o.pressure gauge & test as soon as possible to be safe imo.

As Anna's said, the sender / gauge are awful. Replace sender with a known good one, then purchase a new one if the stocker ends up being bad. If issue still exists, then its most likely your gauge.

Incidentally theres a second o.pressure sender that flash's a red LED on the stock gauge. It'll illuminate at very low pressures.

Edited by GeeTR

How old is the oil? What type is it (mineral / synth)? What grade?

When the oil gets hot, such as after spirited driving as you have done, it becomes "thinner", and can't hold the same pressure at idle.

Absolute pressure is not as important as consistent pressure.

I say check it with a an actual oil pressure gauge. If its still low then change your oil to something heavier until you can find the cause. If I remember correctly, there is a bolt on the bottom side of the oil pump that houses the oil pressure relief valve and spring. You can pull the spring out, stretch it out a bit longer, and reistall. Of course, a clogged oil filter could also be the coulprit. Whens the last time you changed the oil/filter?

IS the engine making any funny noises? No knocks or clacking???

Oil pressure can drop really quick, be just maybe OK when driving, but have bugger all pressure at idle when nasty things happen t your main bearings, like spinning them.... Been there done that...

my R34 is doing the same thing. i mentioned it ot hte mechanic when getting a service, he said it was all fine, got the brand new oil in it, and my guage reads teh same :D

guess mine is faulty

you can pick up a half decent autometer guage for round 150.... or a cheap working one for under 50..... may not be nice, but certainly will give u peace of mind

Hi guys,

Thanks for all of your replies.

The gauge seems to operate okay, and I have found when starting cold the the pressure is halfway between 4 and 8 on startup - I will look into the sender.

My sump although is still half full and I can see no indications of leaks...

The engine is getting slightly louder though, like the injectors and it is only recently that this has started to occur.

I have no idea what oil is in it, because the previous owner put it in. I am guessing from what he said it would be geting near 3000kms- guessing mineral, no idea on grade :) ; but I am going to change the oil ASAP (will have to look up what is in the book for the spec I guess).

Any recommendations? 185 XXX km's on car.

Am going to flush the radiator and refill as well.

:D

Thanks everyone (kuma j, msnismo, GeeTR, blind_elk, rb2240sx, nuclear_skyline, Silver_R34_GT-T) for all of your help :O

Depends on the oil and the condition of the engine.

My RB25DET sits around the '4' mark (? , 1st line up) when everything's good (ie correct oil level in sump) and engine up to operating temp. I'm using Mobil 1 15W50 in an engine rebuilt about 10k ago.

As I said earlier, it doesn't matter what the reading is so much as it's stable.

First thing I'd do is change the oil, that is just good practice since you've only recently bought the car.

It's also possible that there could be a small amount of oil contamination which affects the viscocity of the oil ie: small amounts of petrol escaping past the piston rings and making its way into your oil.

Once you've changed the oil (which imo you should do regardless), and if the problem still persists - get another gauge to test the real pressure. As others have said the oil pressure sender is known to be faulty.

Heres a gooden I learnt... When you drop the oil out, make sure the pan is clean before hand and let the oil run into it...

Dont let it sit for too long and run a magnet through the oil to check for metal in it... If your engines getting louder, and your oil pressure is dropping off, could be a bearing issue...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...