Jump to content
SAU Community

Recommended Posts

The guys that fitted my oil filter relocation kit put it in front of the dipstick on a homemade bracket (flat bar) becuase they reckon they couldn't close the bonnet on the filter.

If someone has one fitted properly to a BNR32 could yous please upload a photo of the filter location on the strut tower plus another where the pipes are run (mine are rubbing on the plenum and that can't be good.

Any advice on a suitable filter to use (the guys chucked the installation manual which had the sizes etc on it )

Thanks! :P:worship::(:worship::)

John

Im about to install mine. I had planned to attach the filter mount to the side of the chassis rail to enable filter changes from below with no mess. I'd be interested in seeing where your cooler core is located. I still have the stock blow off valves so i was planning to put it in front of the radiator.. Where is yours?

hmm lots of changes in that engine bay. boost controller and coil thingy normally lives there. and hicas solenoids. no room unless you've removed them all

I was hoping that was the case - my engine bay is a lot busier - also I don't remember there being right angle connectors (I think mine are straight in) so may not be a Grex kit?

I don't have the oil cooler or other go-hard parts (running std boost) so a stock pic would be perfect....

hmm lots of changes in that engine bay. boost controller and coil thingy normally lives there. and hicas solenoids. no room unless you've removed them all

Yeah I relocated the HICAS....to the bin lol. I'll tidy it up when I do the rebuild...battery to go in the boot. I wouldnt worry about it being legit, it will be...show us a pic.

Heres a pick of the front mount...a little twisting required to fit.

post-24470-1210808949_thumb.jpg

Yeah I relocated the HICAS....to the bin lol. I'll tidy it up when I do the rebuild...battery to go in the boot. I wouldnt worry about it being legit, it will be...show us a pic.

Heres a pick of the front mount...a little twisting required to fit.

thats pretty much how mine is setup..oil relocator n cooler

Heres mine... I use a genuine nissan filter on it

Yours seems to be the same - the restrictor unit and other stuff has been removed/relocated.

I think they've shortened the oil cables/sheaths as well (!)

Here's what my (rather pathetically stock) engine bay looks like:

Does ne1 have a stock engine bay?

There also seems to be something missing - there's a bracket on the tower with nothing on it.....???

yeah that one is stock! except you have the wrong battery (terminals the wrong way around, and larger posts than standard so the cables don't fit properly). You really should not drive it around like that it is in danger of coming loose/shorting/burning the car to the ground.

what holds the other side of the oil filter relocator in place? one side has a bracket going to the strut tower, but what supports the other?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...