Jump to content
SAU Community

Botched Up Grex Oil Filter Relocation Kit R32 Gtr

xfixiate

By xfixiate,
in General Maintenance

 Share

Recommended Posts

xfixiate Rising Star

xfixiate

Posted
Posted

The guys that fitted my oil filter relocation kit put it in front of the dipstick on a homemade bracket (flat bar) becuase they reckon they couldn't close the bonnet on the filter.

If someone has one fitted properly to a BNR32 could yous please upload a photo of the filter location on the strut tower plus another where the pipes are run (mine are rubbing on the plenum and that can't be good.

Any advice on a suitable filter to use (the guys chucked the installation manual which had the sizes etc on it )

Thanks! :P:worship::(:worship::)

John

Godzilla32 Veteran

Godzilla32

Posted
Posted

Im about to install mine. I had planned to attach the filter mount to the side of the chassis rail to enable filter changes from below with no mess. I'd be interested in seeing where your cooler core is located. I still have the stock blow off valves so i was planning to put it in front of the radiator.. Where is yours?

xfixiate Rising Star

xfixiate

Posted
  • Author
Posted
hmm lots of changes in that engine bay. boost controller and coil thingy normally lives there. and hicas solenoids. no room unless you've removed them all

I was hoping that was the case - my engine bay is a lot busier - also I don't remember there being right angle connectors (I think mine are straight in) so may not be a Grex kit?

I don't have the oil cooler or other go-hard parts (running std boost) so a stock pic would be perfect....

Mr. Keets Grand Master

Mr. Keets

Posted
Posted
hmm lots of changes in that engine bay. boost controller and coil thingy normally lives there. and hicas solenoids. no room unless you've removed them all

Yeah I relocated the HICAS....to the bin lol. I'll tidy it up when I do the rebuild...battery to go in the boot. I wouldnt worry about it being legit, it will be...show us a pic.

Heres a pick of the front mount...a little twisting required to fit.

post-24470-1210808949_thumb.jpg

godzl1975 Experienced

godzl1975

Posted
Posted
Yeah I relocated the HICAS....to the bin lol. I'll tidy it up when I do the rebuild...battery to go in the boot. I wouldnt worry about it being legit, it will be...show us a pic.

Heres a pick of the front mount...a little twisting required to fit.

thats pretty much how mine is setup..oil relocator n cooler

xfixiate Rising Star

xfixiate

Posted
  • Author
Posted
Heres mine... I use a genuine nissan filter on it

Yours seems to be the same - the restrictor unit and other stuff has been removed/relocated.

I think they've shortened the oil cables/sheaths as well (!)

Here's what my (rather pathetically stock) engine bay looks like:

Does ne1 have a stock engine bay?

There also seems to be something missing - there's a bracket on the tower with nothing on it.....???

Duncan Grand Master

Duncan

Posted
Posted

yeah that one is stock! except you have the wrong battery (terminals the wrong way around, and larger posts than standard so the cables don't fit properly). You really should not drive it around like that it is in danger of coming loose/shorting/burning the car to the ground.

what holds the other side of the oil filter relocator in place? one side has a bracket going to the strut tower, but what supports the other?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By GTSBoy · Posted

      Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Bireley_32
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Bireley_32 · Posted

      Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • MBS206
      Starting again

      By MBS206 · Posted

      The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...