Jump to content
SAU Community

Recommended Posts

hi guys, i need some help my r33 gtr wheels are scrubbing the rear arches on my r32 gtst what are my options? i don't really want to get them rolled. at the moment ive got just lowering spring but i was thinking of getting coilovers, will these solve the problem? any advice would be good as i need to get my car back on the road the nice weather only last a few months in the UK.

thanks

Link to comment
https://www.sau.com.au/forums/topic/219245-r33-gtr-wheel-on-a-r32-gts-t/
Share on other sites

its not that low the front is fine the back only scrubs when the roads not level or on pot holes but does happen a lot. my car feels very bouncy and i feel every bump in the road. at the moment i've take the rear wheels off but i can get you a picture if that helps. i did think the gap between the rear wheels and the arch would be enough but its obviously not. the gap between the front arches and the wheels is less than the rear but they don't touch.

Coilovers will only help as they are likely to give you a firmer ride, whic means less suspension travel. But it will still rub and a pretty poor bandaid to the problem.

Stick with whtever tyre you have at the front, just put a lower profile tyre on the rear, or even a 235/45 or 235/40. But really, to roll the guards it costs about $50 a corner, its cheap and worth trying

you have 4 options:

increase the camber (may cause added tyre wear)

reduce the tyre size/profile (reduces ur choice in tyre selection)

raise and firm the suspension (will only reduce the scrubbing, wont eliminate it)

roll the guards (if not done properly can ripple the guard lip)

----

Your BEST and only option if you don't want your car looking like a truck is to get a roll done.

I've got R33 GT-R wheels on my R32 GTS-t with coilovers and 235/45 rubber all round - it scrubbed violently over rough surfaces, even after i tried lowering the car and the wheels sat in a little it was still useless before i had a guard roll.

My guards did not get flared out as it was unnecessary with these wheels - only the lip got folded inward with no dramas and the guard looks like normal:

post-2240-1210855236_thumb.jpg

Cheers,

Steve.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...