Jump to content
SAU Community

Recommended Posts

hi guys, i need some help my r33 gtr wheels are scrubbing the rear arches on my r32 gtst what are my options? i don't really want to get them rolled. at the moment ive got just lowering spring but i was thinking of getting coilovers, will these solve the problem? any advice would be good as i need to get my car back on the road the nice weather only last a few months in the UK.

thanks

Link to comment
https://www.sau.com.au/forums/topic/219245-r33-gtr-wheel-on-a-r32-gts-t/
Share on other sites

its not that low the front is fine the back only scrubs when the roads not level or on pot holes but does happen a lot. my car feels very bouncy and i feel every bump in the road. at the moment i've take the rear wheels off but i can get you a picture if that helps. i did think the gap between the rear wheels and the arch would be enough but its obviously not. the gap between the front arches and the wheels is less than the rear but they don't touch.

Coilovers will only help as they are likely to give you a firmer ride, whic means less suspension travel. But it will still rub and a pretty poor bandaid to the problem.

Stick with whtever tyre you have at the front, just put a lower profile tyre on the rear, or even a 235/45 or 235/40. But really, to roll the guards it costs about $50 a corner, its cheap and worth trying

you have 4 options:

increase the camber (may cause added tyre wear)

reduce the tyre size/profile (reduces ur choice in tyre selection)

raise and firm the suspension (will only reduce the scrubbing, wont eliminate it)

roll the guards (if not done properly can ripple the guard lip)

----

Your BEST and only option if you don't want your car looking like a truck is to get a roll done.

I've got R33 GT-R wheels on my R32 GTS-t with coilovers and 235/45 rubber all round - it scrubbed violently over rough surfaces, even after i tried lowering the car and the wheels sat in a little it was still useless before i had a guard roll.

My guards did not get flared out as it was unnecessary with these wheels - only the lip got folded inward with no dramas and the guard looks like normal:

post-2240-1210855236_thumb.jpg

Cheers,

Steve.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...