Jump to content
SAU Community

Why Go From A 20 To 25


Recommended Posts

come on roy boy..

don't bring motorsport in to it.

racing prepared car compared to street car is silly.

You'll agree that a run of the mill VL flexidore is a useless chassis in comparison to an R32 gtst.

possibly good for straight line..

but turning is not it's forte.

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Guest trikdoutvl

the reason ppls skylines handle awsome is cause jap ppl put coil overs n shit n do the suspension rite up, were as commodore nutz suspension aint that high on the list of todo things commpaired to fully hektic sterios n 20 inch mags....... lol

wat basis do u have for a vl chassic is crap commpaided to a r32.... wats to say my standard rb20 vl wouldnt be as fast around the track if i had coilovers n everything the skyline guys bolt on to there cars lol.....

i think the gtr's won in 90 roy with skafie/richards driving, i dont think the group A/walkinshaw won bathurst

skylines chassis would be a better design/stiffer. i say would be as obviously its a bit hard to do back to back testing, but theres been heaps of cases where VL's have run 11's (some faster/some slower) and you cant open the back doors for like half an hour after the run lol

as above..

the VL chassis is not stiff or re-enforced in any way.

how else do you think your LARGER car weighs 100kg less?

also, VL brakes are pretty good.. when they are bolted to a ford laser.

on the VL they are useless.

so these are some of the reasons why a regular VL would be slower on a circuit than a regular R32 GTST

VL turbo brakes are decent enough for a car of its weight. But yes the VL chassis / suspension isnt briliant. But there is plenty of aftermarket parts that will sort that out. Also, comparing a VL to an R32 is a bit rough, its more equitable to an R31. Then again the bulk of the car is dated back to the VB, so other then some small tweaks you woudl have to say the suspension wasnt all that bad, no doubt it aged quickly towards the lates 80s.

There is a VL running around doing track days in Vic with a few guys running VBs and VHs. Considering they only have about 300hp at the engine they are doing damn good times.

Point is they are not that bad you can categorically write them off

Guest trikdoutvl

caint argue with vl brakes being bad lol i call em flintstone breaks LOL..\

titan was talking about why diddnt nissan bring out rb30et's factory... 2 big capacity or something (shrugs)

ive only driven a couple of skylines n neva got to really give 1 a good driving but i giv my vl flogs n it handles good IMO but it does have pedders spring shocks panhard rod strut braces nolethane bushes.. some1 take me for a rap in there skyline with collies :blink:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So left off with high hopes of having a gearbox in pretty quickly........ Got the adapter plate that week and had to chase a few threads and work out how/where everything goes as no instructions. Got the adapter fitted, test fitted gearbox and found had to cut and shave a few things. Tunnel required some hits with a decent hammer to give some clearance on passenger side but it fits with no problems,  could fit a 8hp70 with a little more work. For a cross member I wasn't going to spend $1100 on so shiny machined piece. Went through a few designs and remembered I had a gktech s chassis to cd00# cross member. Fitted that and found its close enough with a few extra bits welded so have gone that way and still a work in progress.  After this got into modifying the intercooler with some bends and clamps. I was procrastinating on this as was not keen to cut up and weld it myself but happy with the outcome.  Onto the radiator shroud and oil cooler mount. This thing took way longer than I thought it would but having to add an extra oil cooler for the trans and wanting everything within the chassis rails its good enough for now. It mounts to the chassis and gives plenty of room for lines and pipes. All the coolers are rubber mounted and sealed the shroud on the top and sides, will use some tape to seal the bottom gap of about 10mm. 20250508_111500.mp4   Next job was to build the new diff and after a delay with a friend got built this week. I ended up putting it all together with supervision and was good to learn how to set one up correctly. I ended up going a 3.69 ratio, nismo 1.5 way gt pro with gtr Axel's. Stripped it all down, gave all the parts a good clean, pressed on new bearings and set backlash. Was good working in a clean assembly room with all the gear. Once got home wire wheeled the case and hit it with some rollbar/chassis black paint. Got a few more bits done but will leave them for the next update.
    • That could be drilled, ground and welded. Would stop it progressing and leaking. But that block shouldn't be pushed very hard, as what you see there is a massive warning sign. But that fix also isn't going to happen properly with the engine in the car, and assembled. So you're looking at anew block if you're doing all that work anyway.
    • It's not as simple as it is being made out to be. It s not hard, but there are things that have to be done. Am busy right now, but will try to essay later.
    • Pinout is different to my knowledge, but you should confirm to be sure. Also you will need to adjust the VQ table in Nistune to suit. I would still recommend sticking with recirculating BOVs, I'm not sure if the R35 card MAF will fully resolve stalling caused by reversion/throttle lift.
    • What issues are those? Previous owner said it wants to stall sometimes. We did test drive and it was nice and smooth so it will be sporadic or idk. And if i just change MAF(the sensor to R35 version) it should be better? And as i asked...is it like "plug n play" with oem MAF from R34?  This is a MAF from R35 right?
×
×
  • Create New...