Jump to content
SAU Community

Recommended Posts

Item: RB25DET

Age: brand new engine

Condition:

Price: $12000 or best offer

To Fit: (What car) anything you want to bolt it to

Location: Newcastle

Contact: [email protected] or via PM

Comments: Full engine package including...

Crack tested bored honed and decked block

Crankshaft linished and balanced with JUN collar fitted

Eagle forged conrods

Aries forged pistons

Total seal piston rings

ACL race series engine bearings

N1 oil pump

N1 water pump

Gates timing belt

OS giken exhaust cam gear

fully reco'd head

256/264 HKS camshafts

Painted engine covers

HKS exhaust manifold

Garrett T04Z turbo

Tial 38mm external wastegate

Plazmaman inlet plenum

850cc SARD injectors

Malpassi fuel regulator

Engine will be sold complete as a drop in, turn key option.

With correctly set-up fuel system and tuning this engine will be good for around 400KW at the wheels.

This engine was recently assembled by another workshop but suffered extensive blow-by due to incorrect clearances. He has gone to a full house RB26 so we are rebuilding it correctly and offering it for sale. Any reasonable offer will be considered including discount for exchange engine.

As a guide we just built a similar long engine (no turbo, manifold, gate, plenum, injectors and reg.) for NYTSKY that came to around $15000. So this represents significant value for money.

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/220530-fully-built-rb25/
Share on other sites

This engine setup was offered to me when Paul and i first got together with my build. As i had already bought all of the parts needed for my build i declined. But i was kicking myself after i got off the phone with him as for the price, you will not get anywhere near what this package can offer.

And the fact there is no waiting,set backs and the hassle of the car being off the road for any length of time, this is a very good deal!

Good luck with it Paul.

P.S Swaps on the turbo setup??? :P

willing to freight to perth

how would it be to send to postcode 6164

cheers

no problem...you arrange freight...our pick-up postcode is 2290

also forgot to add the plenum comes with 80mm billet throttle body

$8000 for long engine only with STD cams and prepped RB26 rods.

Edited by DiRTgarage
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...