Jump to content
SAU Community

Installed My Apexi Pod Filters

R33-RB26DETT
 Share

Recommended Posts

R33-RB26DETT Proficient

R33-RB26DETT

Posted
Posted

Hi guys,

I took my car to the mechanic and he showed me that my 2 air flow meter plugs where disconnected.. He said that this would affect the air flow mixtures and possibly even power output.

Since my car isnt running properly now there is no way to test if this would increase my power now that they are plugged in.

SO what affect would unplugged air flow meters have on a cars preformance, just more fuel bieng pumped into the engine yeah?

Link to comment
https://www.sau.com.au/forums/topic/220638-installed-my-apexi-pod-filters/
Share on other sites
R33-RB26DETT Proficient

R33-RB26DETT

Posted
  • Author
Posted
rev limit = 2500rpm

I'm confused buddy, your saying that it would only rev to 2500 rpm?

But i was redlining it no problems, and it didnt feel like i had lost any power to be honest with you.

I didnt even notice the difference than from the stock air box.

paulr33 Grand Master

paulr33

Posted
Posted

with standard ECU and standard setup if you unplug the airflow meters the RPM will cap at 2500rpm and it will be limp mode

there is no way known the stock ECU would run std maps with airflow meters unplugged, its suicide and the engine has no idea how much air is coming in

double check again or maybe you have some wierd remapped std ecu with a map sensor hack / hks vein setup or something look

look for map sensors and crazy wiring if thats the case

paulr33 Grand Master

paulr33

Posted
Posted

and are you sure he said air flow meters?

it could have been 02 sensors, they are on the dump pipes, the airflow meters are pink labelled plastic things on the air intake pipes

if it was the 02 sensors, the car will run fine, it will just waste a bit of fuel on cruise and your economy wont be the best - no power gain by reconnecting them

R33-RB26DETT Proficient

R33-RB26DETT

Posted
  • Author
Posted
with standard ECU and standard setup if you unplug the airflow meters the RPM will cap at 2500rpm and it will be limp mode

there is no way known the stock ECU would run std maps with airflow meters unplugged, its suicide and the engine has no idea how much air is coming in

double check again or maybe you have some weird remapped std ecu with a map sensor hack / hks vein setup or something look

look for map sensors and crazy wiring if thats the case

Thanks man, i have gone an investigated everything you recommended.

First of all i must have a stock ecu as it has the Nissan seal is still on it:

But someone has cut a red wire from it and tapped up the end so it doesn't short anywhere.. what is this wire and why would they do this? take a look:

post-49206-1211601180_thumb.jpg

Also the i have circled in red the 2 plugs they found disconnected this morning:

post-49206-1211600948_thumb.jpg

I think we are getting closer to an answer thanks again!

R33-RB26DETT Proficient

R33-RB26DETT

Posted
  • Author
Posted
see my pic - ive circled in red the true AFM plug, trace where the wires go

post-2054-1211604327_thumb.jpg

Good news i traced the wire back and its just the O2 sensor.

Ow well no extra power from plugging it in then.. :P

seen that red wire cut before on the ECU before?

cheers for your help buddy.

paulr33 Grand Master

paulr33

Posted
Posted

no worries - yeah 02 sensors unplugged wont cause harm, but you should plug them in, get some better economy

the red wire could be anything - its probably the speed cut wire, does it the stock ecu cap out at 180km/h on the track?

R33-RB26DETT Proficient

R33-RB26DETT

Posted
  • Author
Posted
no worries - yeah 02 sensors unplugged wont cause harm, but you should plug them in, get some better economy

the red wire could be anything - its probably the speed cut wire, does it the stock ecu cap out at 180km/h on the track?

Yeah thats what i thought straight away too.. i havent been to the track yet to test 180km/hr speed cut.

I really want to head down to the track actually so i might become a SAU paying member since i hear they organise heaps of that stuff quite frequently.

R33-RB26DETT Proficient

R33-RB26DETT

Posted
  • Author
Posted
The dudes got a PFC ne way so... :)

Actually dont have one yet, but i am trying to source one atm. Waiting on a few PM's from ppl selling on here.

Thanks for the confirmation of the speed cut wire too nismoid.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...