Jump to content
SAU Community

Recommended Posts

Hi Guys,

I have the following mods done to my car:

Blitz 3" Catback exhaust

Hybrid front mount intercooler

Splitfire coils

Apexi pod

Speed and boost cut removed

Boost Tee

Running 12psi

Just wanted to know what other mods i can do to reach low 12's without changing the engine management.

Would it still be possible to fit a high flowed turbo with a udgraded fuel pump and achieve the desired time.

I would appreciate if someone could point me in the right direction.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/220906-next-mod-for-r34-gtt/
Share on other sites

Turbo - requires management

Injecotrs/AFM etc - requires management

So either way, turbo + ECU, its a 3.5k-4k adventure (with a tune) at the very least to get more power.

You want to know the easiest way to run a low 12?

Put a set of decent tyres on the rear (MT ET Streets). You'll have your time for less than 4 figures.

Also running more boost than factory on the stocker fuel pump is quite risky. They are not known for thier reliability.

BWAHAHAHAHA....Really? Speaking from experience?!! Maybe you should hunt down that camry that axed you first before speaking...or maybe that mazda3? or maybe that celica?

Yeah speaking from experience.

Had a fuel cut in my old skyline before. In the drag strip, got the car off, mid way through the car slowed down due to the fuel cut, rolled down the remainder of the strip and did a 18 secs 1/4 mile in a stockish rb25det.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
×
×
  • Create New...