Jump to content
SAU Community

Gtr Diff - Locking

exXU1
 Share

Recommended Posts

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
rdg engineering have built a full spool for the r200 diff (less rolling weight ) im also sure someone else in oz also makes one as theo woollett had one in his car before the rdg one was finished

Theo smashed the mini spool...save your $$

put a KAAZ 2 way in it...Mark runs 8.0 with one.

or do what i do...run a stocker...hehe

exXU1 Mentor

exXU1

Posted
  • Author
Posted
my stocker is a late model R32 so its a R33 non v-spec diff...1mm larger 1/2 shafts than a R32 early model and 31 spline...the best one in my opinion.

A couple of you may be missing the point - it's not breaking differentials that i am concerned about - rather the fact of one wheel spinning less than the other and sending me across the strip - thats why i want a true locker of types - hence welding her up?

Axles are all being up graded so breakages should be to a minimum, just attempting to aleviate the possiblities of kissing the verticle crete.

BezerkR32 Veteran

BezerkR32

Posted
Posted

a full spool was mentioned. alot safer than a cig centre.

A couple of you may be missing the point - it's not breaking differentials that i am concerned about - rather the fact of one wheel spinning less than the other and sending me across the strip - thats why i want a true locker of types - hence welding her up?

Axles are all being up graded so breakages should be to a minimum, just attempting to aleviate the possiblities of kissing the verticle crete.

2rismo Grand Master

2rismo

Posted
Posted
I was under the impression that ANDRA requires a spool be used.

Are the r33 halfshafts 31 spline and the r32 29 spline. From what ive seen they all have 31 spline input shafts into the diff but just wanted to check that the r33 has larger 31 spline halfshaft.

To the best of my knowledge, ANDRA do not specify diff centre composition. That would just be ridiculous. Think of the types of vehicles you'd exclude.

exXU1 Mentor

exXU1

Posted
  • Author
Posted
I was under the impression that ANDRA requires a spool be used.

Are the r33 halfshafts 31 spline and the r32 29 spline. From what ive seen they all have 31 spline input shafts into the diff but just wanted to check that the r33 has larger 31 spline halfshaft.

MMMMMMMMMM not sure here?

exXU1 Mentor

exXU1

Posted
  • Author
Posted
I was under the impression that ANDRA requires a spool be used.

Are the r33 halfshafts 31 spline and the r32 29 spline. From what ive seen they all have 31 spline input shafts into the diff but just wanted to check that the r33 has larger 31 spline halfshaft.

RDG is giving me a proto type full spool that he has currently designed and he would like to see it put under major load.

.Will let you all know how we go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...