Jump to content
SAU Community

Recommended Posts

ok its been worrying me a fair bit lately, it dosent take a genious to understand that on a cold engine there is no oil around the engine on a cold startup, so on that note, just a quick question, is the car meant to run at higher revs on cold startup then as it gets warmer the revs come down? it almost brings a tear to my eye when i start the car up in the morning and it revs its tits off and slows down.

is this normal?

Link to comment
https://www.sau.com.au/forums/topic/221100-revs-on-cold-startup/
Share on other sites

the longer the engine is cold, the worse the performance, economy and emissions are

the engine's ideal operating temp is 80deg so it does everything possible to heat itself up to 80deg

so below 80deg the ecu adds in fuel and ignition correction to get to operating temp quicker

the longer the engine is cold, the worse the performance, economy and emissions are

the engine's ideal operating temp is 80deg so it does everything possible to heat itself up to 80deg

so below 80deg the ecu adds in fuel and ignition correction to get to operating temp quicker

paul on that comment, are you saying that the longer it takes the engine to warm up to operating temp, the worse it will performe etc.? as in for best performance and economy (at operating temp) its best to warm the engine quicker?

its better to have the engine warm up as quickly as possible, the best way to do this is drive it around normally but dont trash it

tactics such as leaving an engine idle for a 5 minutes before you take off for work is bad, as engine runs colder for longer than it normally would

so drive it around, just dont trash it till the engine temp is up near 60-70deg then its ok for some normal load etc

i usually just baby it around for first few minutes by the time im near the freeway entrace the water temp is well past 55deg so its fine after that

its better to have the engine warm up as quickly as possible, the best way to do this is drive it around normally but dont trash it

tactics such as leaving an engine idle for a 5 minutes before you take off for work is bad, as engine runs colder for longer than it normally would

so drive it around, just dont trash it till the engine temp is up near 60-70deg then its ok for some normal load etc

i usually just baby it around for first few minutes by the time im near the freeway entrace the water temp is well past 55deg so its fine after that

what happens if you do happen to trash it when its cold? does it wear out the engine more?

not that I do it :down:

i used to have a VH commodore, and when starting, would have to apply 50% (keep the engine running) tactics, and 50% (not let it die) tactics, so naturaly the lower the revs the better in that case, because it had no oil at the engine when starting. thats why i asked :down:

An idling engine below 2,000rpm is doin far less damage then when you first pull away and change gears at prolly 3,000rpm+ with the engine under load... So I would not shed a tear on startup, just dont rev out the car at all in the first 10mins... It suprising how long the oil gauge takes to rise... made me realise how useless the water temp gauge is!

Edited by r32line
An idling engine below 2,000rpm is doin far less damage then when you first pull away and change gears at prolly 3,000rpm+ with the engine under load... So I would not shed a tear on startup, just dont rev out the car at all in the first 10mins... It suprising how long the oil gauge takes to rise... made me realise how useless the water temp gauge is!

so your saying its better to let the car warm up in idle for 5 mins?

so your saying its better to let the car warm up in idle for 5 mins?

No, it's not.

Everything else will be stone cold if you leave it idling for 5 minutes...Start it up, wait about 30 seconds, then drive off keeping the revs to a minimum, and everything (gearbox, engine, diff etc) will all warm up

wow, this goes against everything thats been told in the past, if you ask anyone they will say let your car warm up for 5 before driving, why has that been the case all these years and then someone says its bad? surely it must be better to let it idle for 5, otherwise how did everyone come to think that? im not arguing or anything, im just curious, did older cars act differently? and letting older cars warm for 5 be better than driving straight away?

if nothing else (but theres plenty else), the rich mixtures will tend to foul your plugs by idling for minutes on end while cold.

i can practically light my exhaust fumes on cold start lol. so i prefer, start, buckle up, drive off sensibly, wait till oil pressure settles to normal levels, then have fun.

Edited by Munkyb0y
did older cars act differently? and letting older cars warm for 5 be better than driving straight away?

I think in the old days especially if ur carby/choke was out of tune it was probly better to let it idle to warm up rather than have it stall in the middle of the road.

These days u just start up and drive light/normally until the temp is up....

why would you idle for 5 mins? The motor, if under normal mild load, will warm up faster.

if you idle for 5 mins, the gearbox oil, diff oil, all bearings etc are still stone cold.

so you think after 5 mins it's good to go? the engine maybe, but everything else is still stone cold.

best to start up, drive normally after 30s and let it all come up to temperature

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...