Jump to content
SAU Community

Recommended Posts

Its just owning a skyline....

I clean mine every time i take it out for a drive.. u can have as much wax as u like still wont work.

:laugh:

Clean it everytime you go for a drive? I think its safe to say your car is puffing black smoke like a mother f**ker to get that. I dont get any black on my rear bar with my car. I havent cleaned it in over a month and the rear bar is still clean lol

if std ecu

- check CAT

- check 02 sensors

- get a piggyback device to tune the car

if stand alone ecu

- check CAT

- check 02 feedback is supported/enabled

- check 02 sensors

- check AFR's (cruise, half throttle, wide open throttle)

Clean it everytime you go for a drive? I think its safe to say your car is puffing black smoke like a mother f**ker to get that. I dont get any black on my rear bar with my car. I havent cleaned it in over a month and the rear bar is still clean lol

powahhhhhhhhhh

if std ecu

- check CAT

- check 02 sensors

- get a piggyback device to tune the car

if stand alone ecu

- check CAT

- check 02 feedback is supported/enabled

- check 02 sensors

- check AFR's (cruise, half throttle, wide open throttle)

in addition if you have access to Nissan Consult or datascan you can check for error codes. things like coolant temp sensor or detonation sensor circuit errors can put the car into safety mode which means more fuel, retarded timing.

how many km's are you getting to a tank of petrol if you drive normally?

probly about 400-500 driving normaly

thats awesome economy man.

If i got anywhere near that i would be a happy camper...

Id say its just the exhaust and a normal skyline thing... Most of them do it and you just need to keep on top of keeping it clean...

If it gets real bad rub it with a clay bar, give it a quick buff with a polish and throw a wax over the top...

wont last foreva but might make it easier to get it off for a bit :blink:

good luck.

last week i did 380 befor i went to fill up and i still had quarter of a tank left, but i drove normally last week no realy fast take of or pushing the peddle hard as i cant do that at the moment, car loses power quickly if i push it hard thing its afm or fuel pump, i find out sat or sun for my mechanic to fix it should be fun lolz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...