Jump to content
SAU Community

Recommended Posts

HICAS Diagnostic Procedure

1. Input starting conditions for self-diagnosis.

* Turn ignition switch "OFF".

* Set shift lever to "P" or "N" (A/T) or "Neutral" (M/T).

* Turn ignition switch "ON".

* Immediately start engine.

* Turn steering wheel from left to right (at least 20deg from the neutral position) 5- times or more, then depress foot brake pedal at least 5- times all within 10- seconds after ignition switch has been turned "ON".

2. Input self-diagnosis item.

* Depress and release foot brake pedal.

* Turn steering wheel from left to right (at least 20deg) from the neutral position.

* (M/T model):

Depress clutch pedal and move gear shift lever to any position other than Neutral and return to Neutral. Release clutch pedal.

(A/T model):

Disengage and engage parking brake lever. Move shift lever to any position other than Neutral or Parking and return to Parking.

* Move car at least 3 meters (10ft) forward and proceed at indicated speed of at least 2km/h (1mph) in self-diagnosis mode.

3. The self-diagnosis mode will then appear in the "HICAS" warning lamp.

* When all systems are normal HICAS warning lamp flashes at 0.25 second intervals.

* When there is a system malfunction (there is a nifty diagram here of HICAS lamp pulses. I tried to translate them to words...)

Mode A)

10 short pulses for 5 seconds.

No pulses for 5 seconds.

Nine 2-second interval indicating the system status (18 seconds total).

(short pulse = good, 1 second pulse=bad)

1) HICAS Solenoid R.H.

2) HICAS Solenoid L.H.

3) Fail-Safe Valve

4) (Constantly normal mode)

5) Vehicle Speed Sensor

6) Steering Angle Sensor

7) Steering Neutral Position Sensor

8) A/T: Parking brake sensor

___ M/T: Clutch Sensor

9) A/T: Inhibitor Sensor

___ M/T: Neutral Sensor

** Display repeats until ignition switch is turned "OFF" or 5 min has past.

Mode B)

Lamp on for 5 seconds.

No pulses for 5 seconds.

Nine 2-second interval indicating the system status (18 seconds total).

(short (0.1 sec) pulse = good, 1 second pulse=bad)

1) HICAS Solenoid R.H.

2) HICAS Solenoid L.H.

3) Fail-Safe Valve

4) (Constantly normal mode)

5) Vehicle Speed Sensor

6) Steering Angle Sensor

7) Steering Neutral Position Sensor

8) A/T: Parking brake sensor

___ M/T: Clutch Sensor

9) A/T: Inhibitor Sensor

___ M/T: Neutral Sensor

** Display repeats until ignition switch is turned "OFF" or 5 min has past.

Note 1: To change the display mode to "A", turn OFF ignition switch after mode "B" is displayed. When battery is insufficient, mode "B" is displayed.

Note 2: If fail-safe system was operated (fail-safe valve is operating) when ignition switch was turned OFF for the last time, mode A will be displayed. If fail-safe system was not operated when the ignition switch was turned OFF for the last time, mode B will be displayed.

* Canceling the self-diagnosis function

Three methods.

1) By turning the ignition switch off.

2) After self-diagnosis has been operated for ~5 minutes.

3) If the vehicle speed goes over 30 km/h (19 mph).

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/
Share on other sites

What is HICAS? And do I have it?

Good question. HICAS is Nissan’s version of four wheel steering. It is an acronym for High Capacity Actively Controlled Suspension. Unlike other Japanese car manufacturers 4WS (eg Honda’s system) HICAS never exceeds +/- 1°. It is designed for high speed response rather than parking manoeuvres.

The system is electro-hydraulic - the ECU in the boot directs a hydraulic actuator at the rear axle to steer the rear wheels using the rearmost suspension links. The result is usually no more than 0.4° of movement. HICAS gives a touch of counter steer before settling with the rear wheel pointing the same way as the front. (Maybe this explains why my Skyline feels so loose on high-speed gravel...) This results in sharp turn-in, and enhanced stability at medium to high speeds.

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-479806
Share on other sites

What is SUPER HICAS

Nissan Skyline GT-R has the SUPER HICAS setup.

Aided by computer, Super HICAS enables a tightly-controlled power slide that cannot be implemented by any alternatives.

When attacking a corner, the rear wheels will steer in reverse first in order to sharpen the initial steering response. Then, when sensors sense that the car responds to steering, the rear wheels will steer in the same direction as the front wheels, thus immediately introduces rear-tyre slip which help adjusting the attacking angle. Since the computer is monitoring the whole process, the amount of oversteering is always under check. You need not to be afraid of losing control.

The Super HICAS system was also available on a few S13 models. As you can see htat would make drift that little bit easier.

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-479825
Share on other sites

  • 8 months later...
  • 1 month later...

HICAS Diagnostic Mode

There is a HICAS warning light in the instrument cluster. If it comes, on it is indicative of a problem.

R32: Check the HICAS oil level (power steering reservoir in some models, or a remote reservoir accessible from the boot)

R32 and R33: Check all HICAS electrical connections, and if the light remains on, follow the diagnostic below.

Note that having an aftermarket steering wheel fitted without the appropriate HICAS boss adaptor can also cause the HICAS system to show a fault.

  1. Switch ignition off, transmission in neutral or auto in Park.
  2. Start engine
  3. Very quickly (with a couple of seconds), turn the steering wheel left and right about 20 degrees from centre five times, and then pump the brakes five times, then press the brake pedal once more this will enter diagnostic mode.
  4. Drive forwards or backwards about 5 metres at a speed less than 10km/hr, this will enter full diagnostic mode.
  5. The HICAS light in the instrument cluster will be flashing quickly (for normal) or will flash a code indicating any problems.
  6. Long flash = first digit, short flash = second digit.
  7. Diagnostics will return to normal after five minutes, or any speed over 10km/hr,
    or ignition is turned off.

HICAS Diagnostic Codes 1989-1993

1 HICAS solenoid right hand

2 HICAS solenoid left hand

3 Cut off valve

4 Power steering solenoid

5 Vehicle speed sensor

6 Steering angle sensor

7 Neutral position sensor

8 (Auto) Parking brake sensor, (Manual) Clutch sensor

9 (Auto) Inhibitor switch, (Manual) Neutral sensor

HICAS Diagnostic Codes 1993-1999

11 HICAS control unit

12 HICAS motor power supply not present

13 HICAS motor output not present

21 Vehicle speed sensor not present

22 Steering angle sensor not present

23 Steering angle sensor neutral or not present

24 Rear main sensor input not present

25 Rear sub sensor input not present

31 Parking brake sensor input not present

32 (Auto) Inhibitor switch input not present; (Manual) Neutral switch input not present

33 Engine speed signal not present

This information from "The Sky Is The Limit, A Book Of Skyline Stuff"

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-894684
Share on other sites

  • 6 months later...

A couple of questions :(

1) What's the difference (beyond the obvious slight difference in how one enters the mode) between the methods posted by Lozza150 and Greg? Do both methods apply to all Skylines fitted with (Super) HICAS?

2) Using Lozza150's method , does HICAS go in to Mode B by default?

Cheers,

Lucien.

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1130513
Share on other sites

  • 1 month later...

ok I am trying to self check this HICAS light fault.... now the question remains, does HICAS work, or is it marketing? votes for removal on the GTR? and did gibbo's race cars have it removed?

will have to run this check, as the light seems to come on on slight corners or hard accelleration....

ideas?

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1198781
Share on other sites

now the question remains, does HICAS work, or is it marketing? votes for removal on the GTR? and did gibbo's race cars have it removed?

Yes, it works insofar as it does turn the wheels. If that's a positive (it makes manevourability at very low speeds easier) or a negative (you never quite know what the car will do when you start to corner) if up to the driver.

The diagnostic mode should tell you exactly what's wrong.

LW.

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1199297
Share on other sites

Another 2 cents.. I read somewhere that the hicas light will come on if an aftermarket steering wheel is installed and the steering wheel position sensor is not relocated correctly. If i drive in a straight line (open highway) for a couple of minutes without moving the wheel much , my light comes on and stays on till i turn off and restart the car. I know this is my problem as i have a momo steering wheel. Haven't got around to fixing the sensor yet though :cheers:

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1218128
Share on other sites

  • 4 weeks later...

I did the diagnostic and got codes 22 & 23, then as I went back into garage it started flashing quickly (the "good" sign), so I did the diagnostic again and got code 22. BTW I had no probs with the HICAS light before this just did the test out of curiosity.

Are:

22 Steering angle sensor not present

23 Steering angle sensor neutral or not present

big problems for the operation of HICAS?

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1248275
Share on other sites

Hey actually maybe it was a wrong code, because I noted in another post somewhere I think that if you don't drive forward (or back) far enough you can get an erroneous code. I tried this test again twice going forward further and got the HICAS light flashing fast saying everything's ok. In any case unless it causes me any probs I'll leave it be.

On a side note - I've noticed people saying they disable HICAS because it develops problems and aussie mechanics never know how to deal with it, but as far as I know the 300zx had Super HICAS and that was delivered locally so Nissan mechanics at least would know how to fix it, and certainly there'd be others who've fixed 300s?

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1249850
Share on other sites

The Super HICAS system was also available on a few S13 models. As you can see htat would make drift that little bit easier.

It is my understanding that hicas reduces the ability to DRIFT properly as what we are trying to do is loose grip on the tires and therefore DRIFT the rear end about whereas HICAS is trying to steer the tires in a direction that will give more grip according to what the EMS understands what the car is doing.

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1262554
Share on other sites

They say (they being the Engineers) SUPER HICAS provides a sharper turn in ... which might help flick the car out faster then help in the control of the steer.

Remember HICAS and SUPER HICAS only move the rear wheels up to a max of 1 degree

Hicas moves the rear wheels on GTST's 0.7 of a degree

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1262663
Share on other sites

  • 2 weeks later...

OK i swear i read that HICAS doesn't even kick in till about 60km/h ??

is this true ?

also was hicas an option or what ?, what percentage of cars that came out of the factory were fitted with hicas do you guys rekon ?

my mates are always dissing my 32gtst cos its got hicas and apparantly it adds like an extra 100kgs is this right ?

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1277339
Share on other sites

HICAS is at it's most active at high speeds as it is a high speed stability aid more then true 4WS. Can't see it weighing 100kgs. Most people don't even remove it, just "lock" it for drag duties usually.

OK i swear i read that HICAS doesn't even kick in till about 60km/h ??

is this true ?

also was hicas an option or what ?, what percentage of cars that came out of the factory were fitted with hicas do you guys rekon ?

my mates are always dissing my 32gtst cos its got hicas and apparantly it adds like an extra 100kgs is this right ?

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1277773
Share on other sites

  • 2 weeks later...

i hate hicas because i dont understand it..

recently my hicas light is coming on.. and doesnt go away. the only time i have seen my hicas light on is during ignition.. i havent experience hicas before.. when hicas kicks in is the light on the dash lit up? also how do i check that a previous owner hasnt disabled it with a lock kit? and if the hicas fluid needs to be topped up, where do i top it up with and with what? thanks

Link to comment
https://www.sau.com.au/forums/topic/22193-hicas-diagnostic/#findComment-1291117
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...