Jump to content
SAU Community

Recommended Posts

i'm off to get my 2835 installed in a couple of weeks so i decided to do a few of the less time consuming supporting mods myself... (fuel pump etc)

so i installed some new splitfire coils and some bcpr7es gapped to 0.8... and put the car back together

when i took it for a drive i noticed 2 things...

1) it feels smoother and more linear throughout the rev range

2) its running less boost. ?!

formerly i was getting .9 bar with boost controller (bleeder) switched off but spiking out to 1.1

now its getting .5 bar and not spiking past .55

so i turned up the bleed valve to .8 bar and it holds nicely without spiking past .85ish

car has pfc, fmic, turbo back etc. how much boost shold it be producing with these mods?

also when the car was tuned a year ago @ racingline, nige said there was a tiny leek that he didn't have time to locate,(i needed transport back) but the car was running fine and not to worry. the car ran strong for a year with no problems.

so... my question is this...

was the car running with a leek that was acting like a bleed valve and upping the boost for a year

OR

did i not put a hose on properly this time? (i have checked and checked again...)

Link to comment
https://www.sau.com.au/forums/topic/222437-interesting-problem/
Share on other sites

Oh and they're gapped to .8 cause i've been told by many many people that would be the optimum gap...

On a stock ecu/tuned car running 98ron yes

With an aftermarket ecu, tuned and new splitfires your gap should be 1.1..

The idea of setting the gap to .8 is a cheap get around for the pinging/breakdown issues most skylines have on 98ron when using the factory tune.

It's a stop gap, for peeps that can't do it the right way atm...with your parts you shouldn't be bothering with that crap.

Embrace the strength of a bigger spark!!

I did the same thing when I first got my nissan, until I got around to doing it right.

i dunno... taking all that shit off again... might give it a go when i get round to installing those injectors that are still sitting in the box next to my bed :thumbsup:

any ideas on the prob guys?

Even once the coilpacks are "coated in silicon" the car will fart and miss above 5000RPM if you gap is at 1.1mm WHERE IT IS MEANT TO BE!

Once you chuck the Splitfires in, (Or even BRAND NEW stock coilpacks) you will be able to gap plugs to 1.1mm AND rev to redline perfectly cleanly, producing a better flame front in your engine.

Technically, from what I can gather, it will also allow you to run slightly more advanced timing when you do the tune, as you have a wider initial flame front.

Hence @ 1.1mm you should be able to make more power cleanly...

Even once the coilpacks are "coated in silicon" the car will fart and miss above 5000RPM if you gap is at 1.1mm WHERE IT IS MEANT TO BE!

Once you chuck the Splitfires in, (Or even BRAND NEW stock coilpacks) you will be able to gap plugs to 1.1mm AND rev to redline perfectly cleanly, producing a better flame front in your engine.

Technically, from what I can gather, it will also allow you to run slightly more advanced timing when you do the tune, as you have a wider initial flame front.

Hence @ 1.1mm you should be able to make more power cleanly...

Depends on a variety of things but, in this case the 0.8mm gap is going to be better at high rpm/boost and power levels in terms of reliable spark.

1.1mm is a nice gap for a cleaner burn at lower rpm, hence it's factory.

The factory coils are just as good as splitfires by the way. Splitfires are just cheaper to buy new.

Depends on a variety of things but, in this case the 0.8mm gap is going to be better at high rpm/boost and power levels in terms of reliable spark.

1.1mm is a nice gap for a cleaner burn at lower rpm, hence it's factory.

The factory coils are just as good as splitfires by the way. Splitfires are just cheaper to buy new.

How do you figure a smaller spark is better on higher boost?

Gapping down is a very basic and simplistic way of advancing timing...used to get around pinging on a stock non-tunable ecu.

If you tune the car correctly with 1.1 gap it is better...you can actually feel the difference in top end, revs more freely.

Splitfires don't create more horsepower, but they do give a stronger spark (%20?) which certainly helps.

But hey if 8 is your lucky number.... who am I to say different.

How do you figure a smaller spark is better on higher boost?

Gapping down is a very basic and simplistic way of advancing timing...used to get around pinging on a stock non-tunable ecu.

If you tune the car correctly with 1.1 gap it is better...you can actually feel the difference in top end, revs more freely.

Splitfires don't create more horsepower, but they do give a stronger spark (%20?) which certainly helps.

But hey if 8 is your lucky number.... who am I to say different.

I'm sorry but, 'feeling the difference' in top end?

Unless the tune was rooted before I can assure you that not only is there no power difference but, also this 'feeling' is peculiar only to cars that started out with a spark issue or were seriously 'under-gapped' for the density of the air/fuel mixture.

Smashing more power/rpm/boost into a motor and gapping down on the exsisting heat range is tuning 101( for all cars). If you get no joy in the top end after gapping down on the exsisting heat range you go to a colder plug etc.

For example, for most of the NA V8's I've tuned you can just about go off a rule of thumb that is gap down 4 thou for every 50hp added.

I've been doing this to alot of different cars over the years so 'luck' has nothing to do with it. :)

There are some serious horsepower GTST's & GTR's running around with factory coils as well. Splitfires do one thing well and thats make a cheap replacement for the expensive factory coils when they are shagged. :D

Edited by rev210

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...