Jump to content
SAU Community

Recommended Posts

hey guys i need to get my r33 gtst ready for a drift day this weekend, but im currently running no BOV. and it turns out your car stalls inbetween gears with no BOV which isnt a problem on the street but when you handbreaky into a drift the revs die down and it stalls. my question is, does a atmo bov still make your car stall, do i have to go plumb back? thanx guys :P

Link to comment
https://www.sau.com.au/forums/topic/224157-atmo-bov-question/
Share on other sites

Hey Shane,

Plum back will be the sure way, but in saying that if you have you bov tight enough so that is closes fast you should be fine, i Run a blitz and its been fine never had it stall.

If you have management or and safc or similer you can tune that stalling out.

But for the sake of being sure =PLUMBACK :P

yeah i dont want to be anymore cop bait then i already am (skyline driver :P ) but i really need to get my car ready for this weekend and i have a atmo bov laying around. i have a pfc, how do i tune the stalling out??? thanx

hey guys i need to get my r33 gtst ready for a drift day this weekend, but im currently running no BOV. and it turns out your car stalls inbetween gears with no BOV which isnt a problem on the street but when you handbreaky into a drift the revs die down and it stalls. my question is, does a atmo bov still make your car stall, do i have to go plumb back? thanx guys :P

im not sure what you have done, but i am running no bov and i have no issue with stalling during gear changes. and i have done a few drift days with my bov blocked and still no issue

thanx for all the help, im gonna try the atmo for now cuz i have one and cant aford (money and time) to get a plumb back atm. ill let u all know the result. hopfully ill have it done 2moz arvo. and nizmonut, dont coment if its not a helpful one.no one wants to hear useless coments, i already serched but the info i found wasn't what i was asking!!

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
    • lights are on just the one click.  
    • Absolutely matters because, while a temperature change will eventually reach a sensor at the end of a static line, the response time is far far far too slow to be useful. Might as well not have a temp gauge at all.
    • When I was eyeing off the 370GT (after deciding I didn't want to spend 30-40k+ to relive my early 20s in an R33) I thought it'd be a good project to add a turbo to it. Now that I have a 370GT, and I've had a couple of chances to open it up, I'm pretty stunned by how much power it makes 🫠 Honestly, the way the VVEL opens it up, it almost feels like there's a little turbo tucked away in there somewhere. It's like Nissan looked at VTEC and said "hold my beer" 😁 Has anyone thrown a turbo into their 370Z or 370GT? Is there a conservative boost level you can run without having to upgrade the fuel system, or are bigger injectors and a bigger pump a given?
×
×
  • Create New...