Jump to content
SAU Community

Recommended Posts

hey guys got my turbo put on, all tuned on 16.5 psi running 251rwk with all supporting mods.

the turbo does hold boost but as soon as u hit 5,000rpm it just hesitates and drops off to 5 psi. can hear a hiss but cant find it.

took my car for a drive tonight and didnt feel as strong at higher rpm.

boosted it again and it got way worse. in 3rd gear soon as i hit full boost car feels like the brakes are being applied and wont rev anymore.

the first couple of times when its just warming up is fine then it does it. boost was dropping down to 4-5 psi.

turbo is new. checked all my hoses and inspected the turbo and its perfect still.

only thing i can think of what i did last week i wasnt paying attention and i ran up a rounded gutter and cracked my front bar. been doing it since then. few days ago

Edited by R33GOD
Link to comment
https://www.sau.com.au/forums/topic/224398-need-help-r33-gtst-related/
Share on other sites

i have a blitz bov. its atmo

these are my mods

stock internals

hiflowed ball bearing turbo 450hp

splitfires

pfc

blitz fmic

tomei pump

600cc injectors

z32afm

stock intake pipe with k&n air panel filter

full 3in exhaust.

hid boost controller

Edited by R33GOD

have you checked all your pipework? sounds like a leak from something.... try getting under the hood and flicking the throttle cable see if you can hear where the leaks coming from.... as for the car feeling like the brakes have been applied that souds like saftey mode so you dont blow it up....

ok fixed the hose problem but it still drops off boost sometimes.

it only does it when its been thrashed after about 6 times or so.

spoke to my tuner and he thinks it could be my hdi boost controller solenoid getting way too hot. or an actuator issue?

thoughts and experiences if anyones had a ebc prob or actuator prob?

today i further inspected the problem and still couldnt find the prob.

so far i have done a boost leak test.

changed boost controllers

took off front bar inspected cooler and silicon piping

changed all boost line hoses from actuator.

only thing i can think of is maybe the intake pipe is sucking closed.

cause it only does it when u hit the throttle hard on down gear, or at top end as i change hard into 4th. and sometimes 3rd

Edited by R33GOD

it does sound like a boost leak coz at high rpm it drops but if it was it would have given way and popped off hope u work it out! Try connecting a hose straight from the wastegate to the intercooler piping and see what it does then?

ive done everything and soon as the car gets hot after a couple of runs its still doing it.

i done rev210's intake pipe mod also, so i dont know what to do.

only thing i can think of is not enough preload on the actuator. its set to half a hole at the moment.

another theory. if i have faulty plugs and when the car gets real hot would it cause less combustion thus the major boost drop?

mate i had simular prob wif my gtr first noticed it on a trip to melb hit full boost than dropped to half and it would only half boost up after that untill i restarted the car then it was normal again its happined about 3 times now but they have been on really hot days so i just thought it was the ecu in safe mode or something

I'd be doing another boost leak test - if you ran up a gutter and cracked your front bar youve proabbly done somthing to your FMIC or piping. Stick a can of baked beans in the intake and pump it up with an air compressor. make sure you go under the car to listen for leaks too.

I'd be doing another boost leak test - if you ran up a gutter and cracked your front bar youve proabbly done somthing to your FMIC or piping. Stick a can of baked beans in the intake and pump it up with an air compressor. make sure you go under the car to listen for leaks too.

ive taken the fmic out completely and inspected the piping and tanks. they are perfect

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...