Jump to content
SAU Community

Recommended Posts

Make: Nissan

Model: R31 GXE sedan

Milage: 270k

Transmission: 5 speed manual

Colour: bronze

Location: Sydney - North Shore

Complied? Yes

RWC supplied? Yes

Currently registered? Yes - just over 10 months

Price: $1500.00 FIRM

Contact: Myself - Chris - pm here, post here

Comments / Modifications: Has a fulleeee sick pod filter, old cd player, oil pressure gauge, Ti allow wheels and has extractors in the boot ready to be fitted

Car was rego'd back in early May.

I have owned it over a year, it got me to work and back - I can leave it anywhere and not worry about it. It had a bit of drama recently which resulted in a new dizzy and electronic module and a good service. Currently has a low idle which is being fixed.

I am selling as I need a newer car, which is comfy and will be doing longer trips in the newer car.

If you need a cheap daily which you can leave at the station, pub, shopping, then this is the car for you. Leave your r32/33/34/35 at home locked up, and take this out and not worry about it!

It has some minor dents here and there, but for its age, it does the job :P

Cheers,

Chris

I must add, It made 101rwkw!! lol have dyno sheet at work to prove! I'll scan next week though when Im back at work.

(My 33 was at Unigroup and I had to drop something off there, and while we were there it went on the dyno for fun!!)

I can certainly organise some within a couple of days mate :ninja:

(My memory card at the moment is full of my holiday photos lol)

Pics will be up tomorrow, I'll try and clean it also :laugh:

yeah I dunno how it made 101rwkw....my r33 made 255rwkw on the same dyno

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
×
×
  • Create New...