Jump to content
SAU Community

Recommended Posts

Depends on how cold it gets, it's not too thick really as 10w is spec (ASTM D-5293) to flow at -25'c. A good Synthetic will have a lower cP then a mineral though.

The cold doesnt really matter unless its below zero and even lower as most oils can handle the extreme cold and maintain there properties to a certain point.

A 10w-40 oil when the car is started in the morning is 10w when cold which equates to say the viscosity of 90Cs, (The thickness of moving oil is measured in centiStokes or cS) when it its at operating temperature (the last digit "40") ideally it equates to 10Cs. So at 10Cs there is minmal wear to the engine and provides the engine with max protection. Whereas 90Cs is thick and will wear the engine until it reaches operating temp. A 5w-40 will be 70Cs at startup and still be 10Cs at operating temps. A 0w-40 will be say 50Cs when cold and 10Cs at operating temps. All oils are still too thick at startup but wouldnt it make sense to go for the 0w or 5w cause it isnt as thick as a 10w or 15w oil when cold?? The majority of engine wear does occur at startup when the oil has thickened overnight. I would only use a 15w-xx or 20w-xx if it was a very hot day at the track.

I agree with Gohan 0w or 5w and for a worn engine 40 eg. 0w-40, 5w-40. In 10-20years i would go up to 0w-50 or 5w-50

The cold doesnt really matter unless its below zero and even lower as most oils can handle the extreme cold and maintain there properties to a certain point.

A 10w-40 oil when the car is started in the morning is 10w when cold which equates to say the viscosity of 90Cs, (The thickness of moving oil is measured in centiStokes or cS) when it its at operating temperature (the last digit "40") ideally it equates to 10Cs. So at 10Cs there is minmal wear to the engine and provides the engine with max protection. Whereas 90Cs is thick and will wear the engine until it reaches operating temp. A 5w-40 will be 70Cs at startup and still be 10Cs at operating temps. A 0w-40 will be say 50Cs when cold and 10Cs at operating temps. All oils are still too thick at startup but wouldnt it make sense to go for the 0w or 5w cause it isnt as thick as a 10w or 15w oil when cold?? The majority of engine wear does occur at startup when the oil has thickened overnight. I would only use a 15w-xx or 20w-xx if it was a very hot day at the track.

I agree with Gohan 0w or 5w and for a worn engine 40 eg. 0w-40, 5w-40. In 10-20years i would go up to 0w-50 or 5w-50

MMM ok, was going crazy thinking which oil to use, so today i got Motul 8100 ESTER E-TECH (100% syn) 0w-40 5ltr for $89 with NRMA discount (car is 1994 GTS4, 112000Km) got rid of old elf one and put new blodd in there, little bit smooth she run now, not much of a diff yet, will see how it goes.

Was talking to a tech from Motul this morning, and was asking so many questions from him, he advised that 300V version is for racing cars which seek track, and has to change oil every 3000 to 5000K (max) as they are very LACK IN Detergents, since my car is NON-TURBO doesnt need to change that often, I change only like in 10,000K so he recomend 8100 e-tech one for normal street use.

** Got Motul FF LSD Type 2 oil for front and rear diff, and Redline MT90 for gear box today as well, didnt have time to put it tho

##Is it a good idea to use Nulon N70 addictive with Motul FF LSD Type 2 oil or Redline MT90 when i change diff and gear box oil? any comments ....

Cheers

All oils are still too thick at startup but wouldnt it make sense to go for the 0w or 5w cause it isnt as thick as a 10w or 15w oil when cold?? The majority of engine wear does occur at startup when the oil has thickened overnight. I would only use a 15w-xx or 20w-xx if it was a very hot day at the track.

I agree with Gohan 0w or 5w and for a worn engine 40 eg. 0w-40, 5w-40. In 10-20years i would go up to 0w-50 or 5w-50

I agree with the first paragraph but not the second.

Why higher temps for a worn engine? I mean are you saying that you expect your engine to run hotter as it gets more warn and will therefore need a oil with a higher number at the end (forget the technical term for this :laugh:)?

I've been told to keep the numbers closer together, so 0w30 is good is you are not hitting temps like 110degrees (or was it a bit less)? At that point the oil is too thin and you should be using something w40....or even higher if you are a track car...

Regards,

Gareth

I agree with the first paragraph but not the second.

Why higher temps for a worn engine? I mean are you saying that you expect your engine to run hotter as it gets more warn and will therefore need a oil with a higher number at the end (forget the technical term for this :) )?

I've been told to keep the numbers closer together, so 0w30 is good is you are not hitting temps like 110degrees (or was it a bit less)? At that point the oil is too thin and you should be using something w40....or even higher if you are a track car...

Regards,

Gareth

My understanding of increasing the oil viscosity is to maintain the pressure of the oil. Each car has an ideal pressure @ x rpm, in order to maintain this pressure a thicker oil is used to achieve this. I see alot of people using a xw-40 or thicker oil for GTR's even though the manual states a 7.5w-30 oil. Same goes for other sites, skylines or not.

I have also heard to keep the oils numbers closer together. Oils which span a large range i.e 0w-50 have alot more additives in it to make it that type of oil and as time goes on these additives break down and you will no longer have a 0w-50 oil. It may be a 5w-50 or 10w-50 for sythetic oils but if its a mineral oil the 50 drops to say 40. So if you change your oil often it should be ok. Only real way of knowing is to get your oil tested at a lab to see how much your oil has broken down over time.

just checked the weather, next saturday's track day for some of us Vic peeps (some_cs_student, myself, etc).... 35 freakin degrees!!!

i've got some 5w30 royal purple coming from Harold, as there has been some issues recently that Moil and Castrol have switched to group III oil for Mobil 1 and Syntec (maybe not 0w30 syntec)

BUT, for the oil guru's, do you think Royal Purple 5w30 will be able to handle a track day when the air temp is 35 degrees and god knows what the track temp will be

  • 2 weeks later...

Ugh...

I came to this thread to determine which oil I should go for... now I'm more confused than ever :rofl:

I was thinking perhaps one of the Motul blends, but I dunno. Not sure if anyone sells it local to me anyway.

What are you R34GTT mild tune owners using?

Cheers

For the average street/daily user I strongly believe you really can't go wrong with the Motul 8100 5w40.

I recently had the head off after 70,000km's of use; it was super clean. Bores looked perfect. I couldn't ask for anything more.

If the car is tracked often; not so much of a daily or can justify spending the $$ the 300v is the stuff to use. :rofl:

After putting the head back on I decided to switch to Shell Synthetic 5w40 the cheap grp3 stuff.

All appeared ok apart from when the oil change approached 4000km's and then cut the filter open at 5000k.

As 4000k approached the lifters would begin to tick slightly on cold start up; nothing major just a slight tick more times than not first thing in the morning.

Cut the filter open - There was a smear of what looked like grease in the inner groove of the pleates.

Motul 8100 5w40 went back in; when that was due an oil change I cracked the filter again; damn it was perfectly clean no lumps of what looked like grease. and lifters had not ticked at all.

So back in went the shell synth 5w40; out it came a 5000k later and there were the lumps of grease again and the lifter tick had returned towards the end of the 5k. :S

I'm not completely sure what was going on with the shell stuff; maybe just a coincidence.

It was black and white to myself as I repeated the test over a couple of times.

For the price the Motul 8100 5w40 really is the best bang for buck. Its a full grp4 base stock PAO oil.

There's no other oil available for that price that is a PAO oil. :D

Shell, castrol etc are all poo grp3 oils.

For the average street/daily user I strongly believe you really can't go wrong with the Motul 8100 5w40.

i wanted to use a 5w30 (just because nissan recommends a 7.5w30), but that means i'd have to go with Motul 8100 ester e-tech, coz as u said, the Motul 8100 xcess only comes in 5w40

is 5w40 acceptable for 115km rb25?

also, whats the verdict on royal purple motor oil (not racing oil)? is it just all hype and marketing? Ive heard so many conflicting reports about it, i'm going to stay away.

Edited by Munkyb0y
For the average street/daily user I strongly believe you really can't go wrong with the Motul 8100 5w40.

I recently had the head off after 70,000km's of use; it was super clean. Bores looked perfect. I couldn't ask for anything more.

If the car is tracked often; not so much of a daily or can justify spending the $ the 300v is the stuff to use. :D

After putting the head back on I decided to switch to Shell Synthetic 5w40 the cheap grp3 stuff.

All appeared ok apart from when the oil change approached 4000km's and then cut the filter open at 5000k.

As 4000k approached the lifters would begin to tick slightly on cold start up; nothing major just a slight tick more times than not first thing in the morning.

Cut the filter open - There was a smear of what looked like grease in the inner groove of the pleates.

Motul 8100 5w40 went back in; when that was due an oil change I cracked the filter again; damn it was perfectly clean no lumps of what looked like grease. and lifters had not ticked at all.

So back in went the shell synth 5w40; out it came a 5000k later and there were the lumps of grease again and the lifter tick had returned towards the end of the 5k. :S

I'm not completely sure what was going on with the shell stuff; maybe just a coincidence.

It was black and white to myself as I repeated the test over a couple of times.

For the price the Motul 8100 5w40 really is the best bang for buck. Its a full grp4 base stock PAO oil.

There's no other oil available for that price that is a PAO oil. :D

Shell, castrol etc are all poo grp3 oils.

A pretty good endorsement for Motul 8100 Cubes :D

Out of interest, roughly how much does 8100 cost?

Thanks :O

far out cubes how many Km's have you done in your car?

7years and ~200,000km's of my own km's.

i wanted to use a 5w30 (just because nissan recommends a 7.5w30), but that means i'd have to go with Motul 8100 ester e-tech, coz as u said, the Motul 8100 xcess only comes in 5w40

is 5w40 acceptable for 115km rb25?

also, whats the verdict on royal purple motor oil (not racing oil)? is it just all hype and marketing? Ive heard so many conflicting reports about it, i'm going to stay away.

I ran it in the old RB20 from ~70,000km's to 180,000km's on the clock and also in the RB30DET that now has 80,000km's under its belt.

RB20 still looked good when I pulled it out; comp ratio was perfect as was oil pressure.

A pretty good endorsement for Motul 8100 Cubes :D

Out of interest, roughly how much does 8100 cost?

Its often $59 at Autobarn or motoquip.

Last time I bought it at Autobarn they slugged me $64 for it but the label price was $59 so they refunded the $5 and I got it for the label price :D

i wanted to use a 5w30 (just because nissan recommends a 7.5w30), but that means i'd have to go with Motul 8100 ester e-tech, coz as u said, the Motul 8100 xcess only comes in 5w40

is 5w40 acceptable for 115km rb25?

also, whats the verdict on royal purple motor oil (not racing oil)? is it just all hype and marketing? Ive heard so many conflicting reports about it, i'm going to stay away.

I ran it in the old RB20 from ~70,000km's to 180,000km's on the clock and also in the RB30DET that now has 80,000km's under its belt.

RB20 still looked good when I pulled it out; comp ratio was perfect as was oil pressure.

sorry man. ran what? Royal Purple or 8100 5w40?

Edited by Munkyb0y

from what i've found, its around the $90 mark.

but as i said, there are so many conflicting reports on this stuff. some people swear by it, others say its sub standard. and the company itself doesnt seem to disclose much.

anyway, i think i'll go the 8100 5w40. seems very well priced.

Edited by Munkyb0y
Its often $59 at Autobarn or motoquip.

Last time I bought it at Autobarn they slugged me $64 for it but the label price was $59 so they refunded the $5 and I got it for the label price :D

A reasonable price, thanks for the help

Royal Purple is a true GrpIV oil.... there have been reports Mobil 1 and Castrol Syntec have dropped back to GrpIII without telling anyone as they reckon it's "near enough" to a full synthetic, so feel they didn't have to tell anyone :)

Put Royal Purple in my 34, and will probably stick with it, bout $70 for 5litres. It copped a few saturdays ago, 30+ degrees, Sandown (track day), oil temps never above about 105 degrees, and the oil pressure was good throughout the day. Haven't checked it yet, but seemed to do it's job on the track on a very hot day.

Put Royal Purple in my 34, and will probably stick with it, bout $70 for 5litres. It copped a few saturdays ago, 30+ degrees, Sandown (track day), oil temps never above about 105 degrees, and the oil pressure was good throughout the day. Haven't checked it yet, but seemed to do it's job on the track on a very hot day.

$70 for 5 litres? Try Harold from Performancelub next time.

His oils are cheap and he sells the "German" castrol, I might try Royal Purple next.

Regards,

Gareth

hey Gareth :(, i got it from harold, $11.99 per quart, and you need about 6, $71 - i was just putting it into a more friendly measurement, litres instead of quarts. But it's still around $70 for an oil change

didn't i tell you about Harold!? :blink:

That's what i was referring to, German Castrol, Castrol Syntec. It seems anything OTHER than 0w30 is made in the US with GrpIII grade oil, and oil the 0w30 is made in Germany from GrpIV. Who knows really...

so that's why i went with RP. Might do a bit more research and give the Castrol 0w30 a shot if i can confirm it's still GrpIV

ive been using mobile 1 5w-50w.(Fully Syn) However im finding 50 a little bit too thick, as i am getting some lifter noises. What i am plan to do is move on to mobile 1 0w-40w. (Fully Syn). and i might add some "lifter free" to try and clean out those lifters.

What do u guys think off this?

From what ive read so far, it seems that it should be a good swap. But extra info is always good =)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...