Jump to content
SAU Community

Recommended Posts

  • Replies 268
  • Created
  • Last Reply

Top Posters In This Topic

My 2 cents on the thread topic..

GTR > GTS-T (and no before you think, this is not a biased comment it is a factual one).

I owned a R32 GTS-T way back when I was 20. It was my first "performance" car and I loved it.

But after having owned now two GTR's they just do not compare at all. They make look (exterior-wise) very similar, but thats where similarities end..........

On the track there are some GTSTs that can keep up with the GTRs. However, ask those GTST owners how much they spent on their car before they can catch up with the GTRs.

It really depends on how much money you can input into your car. Whoever has the 'dough' wins the race.

How bout the upkeep on a gtr? Ive read in magazine's they are very expensive to keep and to look after? also if your motor go's your lookin at a 10,000 rebuild ofcourse with forgies! but do you need money even just to own one without modification?

GTR's do have the potential to cost $$$ if something major goes wrong. But so does other high performance cars.

The RB26 motor is not made out of paper. It is one of then most well built motors that ever came out of Japan. If you buy one that has been looked after and then you look after it yourself (i.e. don't thrash it), servicing is quite resonable (on par with servicing a V8).

Any perfomance car is going to cost you more $$$ to own/service than a non performance car.

But back to your topic...

If you are asking whether a stock GTR has a huge difference in performance compared to a GTS-T then yes, it does.

You can't compare them fairly if lots of dollars has been poured into a GTS-T and then no dollars into a GTR.

Edited by im late

its exactly the reason why i'm really trying to stop modding my GTT...i dont wanna spend anymore than i have to coz i know one day i'l want a GTR...but then the GTR is so much more expensive to modify depending on how far you're willing to go... :(

blah blah blah.. sheesh, you wanna go drifting in a gtr pull the damn fuse. sheesh. same goes for a gts4, get one of those and a rb30 block for your 25 head you are on your way to caining the arse off alot of gtrs.

if so in a drag the gtr would have a better start but how bout the finish would the rearwheel be anybetter than the 4wd system?

I just read alot of junk mags and in one they said a rwdrive is superior at the high speed compared to the 4wd?

Let us know your thoughts

^^ lol

Well the GTR's 4wd system isn't constant so if it's not spinning the back tyres then it's not splitting torque to the front wheels (although there is about 5%ish split to the front in 33s and 34s).

as bubba said, that 5% is bugger all when the rears arnt breaking traction, so id say the only advantage the gtst would have over the gtr is the fact it isnt carrying a front diff, center diff and its associated driveline components, however in saying that the gtr has the advantage of extra capacity, and more advanced engine work over the gtst, i would say better tuned ecu but for penny's these days you can have that changed in hours.

ok if you want a car that goes fast its a gtr, one thing i have learnt is it costs to much to make a pile of s**t fast and reliable just start of with a fast car and go from there, if you want a show pony get a gtst but neva try putting it up agains a gtr because it will lose even if you do beat it have a look in ya wallet and i bet you have lost. so if you want to do it do it right the first time spent the extra and get a gtr.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...