Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

Umm, guys, just thought I'd say something, the original manifold keeps being referred to as "stock extractors". They aren't, the original one is just a cast iron exhaust manifold. Extractors are as the Coby ones- e.g tubular, better flow than stock. Actualy, "Tube Headers" is more accurate as a term, as extractors are really only a particular design of tubular headers which act to "extract" gas from the cylinder by clever use of cylinder pulses.

cheers,

floody

  • 4 weeks later...

hey guys, i've finally fitted the coby extractors on the car. cost $99. car is much more responsive from around 2500 rpm. i've ended up taking the pod filter off and putting the stock box on with trust panel filter, the sound is soo lound with the pod on!

only prob i have now is that for some reason it hangs low like dogs balls and scrapes on my driveway :P not sure which part exactly is scraping, i suspect its the part where it bends. gotta get outta the car and have a proper look.

hey denny,

its weird, my fuel economy slightly improved?! the extractors do hang quite low don't they, it makes me reluctant to lower my car.

i will organise that dyno day we spoke about as soon as i finish my exams (november 10) so a few of us n/a guys can compare numbers and not feel uncomfortable about the big numbers the turbos pull :( is there anything to 'tune' on a standard skyline? i was told u need at least SAFC or something before dyno tuning is worthwhile?

cheers

greg

hey greg, with a standard skyline i guess all they can do is advance the ignition timing. i've actually got the old school generation 1 safc, the one with the knobs on it lol. theres only like 5 tuning points though. i picked it up really cheap so thought might as well give it a try. anyone else got ? u can turn it up -30 or +30, i take it when u go towards minus thats leaning it out?

Originally posted by _turtle_

hey guys, i've finally fitted the coby extractors on the car.  cost $99.  car is much more responsive from around 2500 rpm.  i've ended up taking the pod filter off and putting the stock box on with trust panel filter, the sound is soo lound with the pod on!

only prob i have now is that for some reason it hangs low like dogs balls and scrapes on my driveway :)  not sure which part exactly is scraping, i suspect its the part where it bends.  gotta get outta the car and have a proper look.

they only cost $99?? what the fudge?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...