Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

Umm, guys, just thought I'd say something, the original manifold keeps being referred to as "stock extractors". They aren't, the original one is just a cast iron exhaust manifold. Extractors are as the Coby ones- e.g tubular, better flow than stock. Actualy, "Tube Headers" is more accurate as a term, as extractors are really only a particular design of tubular headers which act to "extract" gas from the cylinder by clever use of cylinder pulses.

cheers,

floody

  • 4 weeks later...

hey guys, i've finally fitted the coby extractors on the car. cost $99. car is much more responsive from around 2500 rpm. i've ended up taking the pod filter off and putting the stock box on with trust panel filter, the sound is soo lound with the pod on!

only prob i have now is that for some reason it hangs low like dogs balls and scrapes on my driveway :P not sure which part exactly is scraping, i suspect its the part where it bends. gotta get outta the car and have a proper look.

hey denny,

its weird, my fuel economy slightly improved?! the extractors do hang quite low don't they, it makes me reluctant to lower my car.

i will organise that dyno day we spoke about as soon as i finish my exams (november 10) so a few of us n/a guys can compare numbers and not feel uncomfortable about the big numbers the turbos pull :( is there anything to 'tune' on a standard skyline? i was told u need at least SAFC or something before dyno tuning is worthwhile?

cheers

greg

hey greg, with a standard skyline i guess all they can do is advance the ignition timing. i've actually got the old school generation 1 safc, the one with the knobs on it lol. theres only like 5 tuning points though. i picked it up really cheap so thought might as well give it a try. anyone else got ? u can turn it up -30 or +30, i take it when u go towards minus thats leaning it out?

Originally posted by _turtle_

hey guys, i've finally fitted the coby extractors on the car.  cost $99.  car is much more responsive from around 2500 rpm.  i've ended up taking the pod filter off and putting the stock box on with trust panel filter, the sound is soo lound with the pod on!

only prob i have now is that for some reason it hangs low like dogs balls and scrapes on my driveway :)  not sure which part exactly is scraping, i suspect its the part where it bends.  gotta get outta the car and have a proper look.

they only cost $99?? what the fudge?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...