Jump to content
SAU Community

Kung Fu Panda

gazal

By gazal,
in Victoria

 Share

Recommended Posts

ITZTRU Proficient

ITZTRU

Posted
Posted
Anyone planning to watch it? Saw the movie trailer while wathcing HULK thought it was pretty funny..

I saw the trailer while indiana jones i think...i was thinkin i might watch it if i get a chance...what did u think of the Hulk?

Link to comment
https://www.sau.com.au/forums/topic/225682-kung-fu-panda/#findComment-3974617
Share on other sites
gazal Collaborator

gazal

Posted
  • Author
Posted
what did u think of the Hulk?

The Hulk was so so i prefer the first obe with Eric Banner... dunno why they made another one.. Yeah planning to see Get smart as well.. I used to watch it a lot when i was a kid plus the cartoon version as well. If memory serves me well i think the cartoon version used to been shown on channel 2..

Link to comment
https://www.sau.com.au/forums/topic/225682-kung-fu-panda/#findComment-3975137
Share on other sites
llama_au Grand Master

llama_au

Posted
Posted

I liked Kung Fu Panda, but it wasn't that funny. I wanted to see it for the graphics. On the other hand I absolutely loved Hulk and Get Smart (which I saw on Thursday) would be the funniest movie I've seen all year. It's a must watch.

Link to comment
https://www.sau.com.au/forums/topic/225682-kung-fu-panda/#findComment-3977063
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
×
×
  • Create New...