Jump to content
SAU Community

Recommended Posts

  • Replies 120
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by adam 32

how would you bring boost on earlier with a more agressive timing curve? surely it will still flow the same amount of exhaust gas therefore the turbo will always spooll at 4K?

Ask steve @ sst. I wont be going down the drags till I have the wolf3d in and tuned. Dont see the point in going until the car's setup right, plus my tyres are hitting about 12 months in age, although not completely lacking in tread I'm sure they wont be as good as new ones but I'll still give them a try. I think my stock ecu is ****ed, in the mornings (cold or not) the car searches up and down, sometimes to the point of stalling but doesnt quite and then finally settles on about 1500rpm till it warms up and then sits around 650rpm, sometimes the car idle is lumpy too, but I think thats spark plug related.

Originally posted by rob77

I think my stock ecu is ****ed, in the mornings (cold or not) the car searches up and down, sometimes to the point of stalling but doesnt quite and then finally settles on about 1500rpm till it warms up and then sits around 650rpm.

Mine does that. Grant told me what it was. Can't remember now, something is a little out of calibration. Computers not f#cked.

Originally posted by Hicks

Mine does that. Grant told me what it was. Can't remember now, something is a little out of calibration. Computers not f#cked.

Mine does the hunting thing too on cold startup every now and then.. I find a tap of right foot seems to sort it out pronto tho..

Robbie i dont think you will reduce your lag marginally with an exhaust manifold change

Your kidding yourself, the ex housing is too big and the efficiancy range is way off what boost your stock internals can handle

Im guessing 100rpm better spoolup with the manifold. maybe 100 rpm more with the tuned computer but even that is optimistic

down the drags you poofs

Originally posted by caminperth

Any ideas when I can use those tickets you gave me rev?

At "The Clink" in freo, this friday night. Event starts at 10pm goes to 1am or so. I may or may not be presiding over part of the nights event, subject to my wife being there. :)

Originally posted by macka

Your kidding yourself, the ex housing is too big and the efficiancy range is way off what boost your stock internals can handle

The stock internals are pretty strong, the problem is the RB25 compression is a tad too high to start with.

Rob's got a 'cadbury turbo', a bar and a half of full boost.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...