Jump to content
SAU Community

Recommended Posts

Hi All,

Hoping I could get some advice. I have checked the forums and kind find anything relevant to my situation.

Last night I absolutely thrashed my R32 gts-t for about 15-20 minutes. My younger brother then gave it a go and revved out 1st gear many times. This morning, driving to work I noticed the following problems.

1. 1st - 2nd gear change grinds if done quickly. Difficult to put it in if done slowly.

2. slight shudder when pulling away in 1st (slowly).

I tested it again at lunchtime, the shudder seems to have dissapeared, however the 1st-2nd problem is still there.

I doubt the gear oil has been changed in a while so I have it booked in tomorrow. If this does not alleviate the problem then I assume the syncro between these gears will need to be adjusted. Any suggestions/advice?

Thankyou

Edited by Tristan21
Link to comment
https://www.sau.com.au/forums/topic/227511-possible-syncro-issues/
Share on other sites

LoL

The shudder could have been from the clutch friction plate. You could have overheated it, which's then made it slightly unbalanced. That could explain how it went away after driving for a while.

Do a g.box oil change, if you know its been a while - go from there.

LoL

The shudder could have been from the clutch friction plate. You could have overheated it, which's then made it slightly unbalanced. That could explain how it went away after driving for a while.

Do a g.box oil change, if you know its been a while - go from there.

Thanks mate

Shudder will be from the clutch, and it sounds like you shagged 2'nd gear synchro. It might work better with fresh oil.... might not. If not, better off fixing sooner rather than later, because it will just damage the selector sleeves and cost you even more money. R32 GTST boxes are cheap compared to R33/R34/GTR, so probably the quickest option would be a second-hand box from an importer.

Well I have changed the gear oil to a synthetic, seems a little better but still not perfect. Any idea how much a 2nd hand gearbox will go for?

I also had the clutch replaced, shudder is now gone.

Thanks guys

When you get your gearbox oil changed, check how much metal shavings have been collected on the magnet at the bottom of your gearbox, this will determine how much thrashing you are giving your gearbox..

I recently changed my gearbox fluid at home with a mate, and i discovered 3 clips attracted to the magnet, my mate reckons they look like linkage clips, whatever they may be, its not good, even though i still can change gears smoothly, i get grinding in 3rd and 4th gear when flat changing..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...