Jump to content
SAU Community

Recommended Posts

In case anyone is interested there's a great thread in forced induction on a new Australian plug in ECU for rb20/25/26

http://www.skylinesaustralia.com/forums/Pl...ng-t218179.html

Briefly :

Direct plug and play replacement ecu board

full usb software tuning

switchable maps

uses all factory sensors

built in map sensor

boost control

launch control

antilag

built in factory base map for local fuel

australian built with full support and warranty

much much more

Cost will be around $1650 . Although more than a base powerfc , if you add up boost controller , map sensor or AFM upgrade and laptop software for PFC its pretty competitive - a 2nd hand rb25 power fc and decent electronic boost controller is probably more.

Were hoping to have the 1st units early next week and we will be carrying them in stock.

I am posting here as I think its pretty big news given the lack of power fc options for rb25/20. If any mods think that's not appropriate feel free to move to the sponsor sale section and my apologies.

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

anyone who can tune a powerfc/wolf/haltech/motec/autronic etc will have no problem . software is very good and stable

well also be able to arrange tuning for them

hows the tuning time going to compare against something like a powerfc? will more time be needed on this new ecu which would mean more tuning $$$ or is it easy to work with?

hows the tuning time going to compare against something like a powerfc? will more time be needed on this new ecu which would mean more tuning $$ or is it easy to work with?

early reports are tuning software is great . easy to use and reliable . time will be similar to pfc or any other popular ecu

tuners I have spoken to over east are quoting normal tuning prices same as pfc

So I can hook up a laptop if I have the right cable and adjust the boost or can only tuners modify it?

usb is built in , plug into your laptop and tweek to you hearts delight . im not sure on tuner lockout options at this stage but certainly its not a requirement

also has the ability to run multiple maps via assignable input , ie multiple boost settings . I believe cool stuff like gear/rpm dependent boost mapping is also supported (have to confirm )

Edited by autoworx
can these be used without AFMs? like a d-jetro? as my AFM's seem to be stuffed..

Yes.

Briefly :

Direct plug and play replacement ecu board

full usb software tuning

switchable maps

uses all factory sensors

built in map sensor

We will be putting one on our "big china turbo" equipped drift/track bunky r33 for testing purposes.

the forced induction thread linked at the top is getting the first few install reports coming through and they seem to be awesome

1st shipment arrives today!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...