Jump to content
SAU Community

Recommended Posts

Just get it rego'd in tassie as SI on a rally log book and you don't have to worry about complied.

I don't know that its a huge job to convert a non-abs to abs since the ACD uses the abs sensors for wheels speed, so they already have that part covered.

Yeh I was pretty certain the cutoff year was and would be for the forseable future 2002, not sure where the idea that it increases every year came from.

That said VII it is?

Probably not ideal for tarmac but this is pretty damn cool, might see it at the Burger ring in June yet!

Lexus-IS-F-CCS-R-on-2011-Tokyo-Auto-Salon-front-side-view.jpg

WTF is that Timmay? A Subaru or something? It's icky :P

Yeah a 7 is the cutoff I believe..... not sure where the rolling year idea came from, maybe from Gus who was planning on running his Spec C in EM once it was elligible?

worse than a subie, it's a expensive toyota.

You can chuck the good ol commodore abs unit resnobly easy if you get a non abs model.

You would pick up an emo abs unit that would just fit too, plenty around.

Retro fitting the ABS can be a right pain in the arse. The hubs on the RS dont have the hole in them to fit the speed sensor so you need for hubs. The driveshafts dont have the ABS gear on them so you need to replace them. Then you need the AYC ECU and the yaw sensors and then figure out how to wire it up. :)

Preference would definately be to have one already equipped.

Glad to hear the date isnt shifting. After looking into classics Stu advised that the date after being shifted to 1985, is likely to stay that way for some time to avoid the goalposts consistently shifting as to what is the best car to be in. Would have hoped they were doing a similar thing for EM. I guess a revision about once every 10 years would make sense. Apparently it was about 15 years before classic got revised from 1980 to 85.

So a VII would be the pick out of the EMO range. Or really, get an 8MR RS and despec it to be a VII. The precedent has been set. :)

The RS has proper mechanical diff in the rear, the actual change is quite a lot from a GSR, you have to change basically the majority of the rear subframe, diff housing, axles, tailshaft and centre diff.

As this is what we did to Millars old IX.

True, precedent set ;)

What is the advantage besides an alloy roof?

To be honest Woo I am not quite sure on all of it. It was mainly the ali roof, slightly updated ACD software (they are reflashing the factory ACD ECU's now so no biggie) the VIII MR had slightly more aggressive cams, (different cam timing stock, same lift and duration) and a different huffer and thats about all I got off the top of my head.

You do pay a bit of a premium for the MR so maybe not worth it for largely a few kgs off the roof.

There were some MR RS's but they were rare as the proverbial. As Tim suggested, doing a GSR to RS conversion can be done but it is a little bit of work. With my TME it was just a RS diff centre, driveshafts and "moustache" (diff support) bar and subframe to do the swap. Tailshaft was sweet. Centre diff was sweet as well.

From my experience, you are best off trying to get as close a spec as you can out of the box rather than arsing around trying to turn something into something its not. A VII RS with ABS would be sweet if they exist, or possibly an 8MR RS if you can find one. Or an VIII RS I guess. Then its just a front bar, bonnet and rear wing essentially and you have a VII.

You would just go a motec diff controller anyway, or a ralliart controller (which I happen to know where there is one sitting :D)

Just not convinced you could take an VIII and run it as a VII just by changing bumpers

So how loose are the rules for Classics up to '85. I had plenty of time whilst waiting by the side of the road and thought of a pretty cheap and fun Classic MS car. Looking at some of the Torana's/ Mustangs I think I could put something through a sausage machine that would be fun and and pretty cheap, that once in a while could be pretty quick :)

And all this talk of Evos must make your vaginas sore? If you need 2L AWD then go R32 GTS-4 baby but seriously...Cossie Escort all the way!!!!! Every 2-3 months I look at all the cool Grp N ones you can buy out of Europe for almost a song. Most LHD but some RHD. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...