Jump to content
SAU Community

Recommended Posts

Hey all,

My 94 r33 gts-t Skyline is coming up to to its 200,000KM mark and was wondering do I need to get anything different done then a 100,000KM service?

And also if it is "worth" trying to add on more performance modifications if the KM's are this high.

I'm a car noob so please don't hurt me. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/
Share on other sites

Hey all,

My 94 r33 gts-t Skyline is coming up to to its 200,000KM mark and was wondering do I need to get anything different done then a 100,000KM service?

And also if it is "worth" trying to add on more performance modifications if the KM's are this high.

I'm a car noob so please don't hurt me. Thanks.

not really much difference aslong as everything has been fixed/changed at the 100,000km service point. its only another 100,000km service pretty much. obviously at that age a compression test should be done but you should do that at the 100km aswell.

if it has been looked after there i don't see a problem. maybe all fuel lines, vacuum hoses etc should be checked and replaced if you haven't done so.

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4032667
Share on other sites

Hey all,

My 94 r33 gts-t Skyline is coming up to to its 200,000KM mark and was wondering do I need to get anything different done then a 100,000KM service?

And also if it is "worth" trying to add on more performance modifications if the KM's are this high.

I'm a car noob so please don't hurt me. Thanks.

you should replace some of the ignition parts...i.e. coils, if you haven't replaced them yet, they start failing around the 200k mark...also check some of the electronics, i.e., water pumps.

have u ever gotten a carbon flush? if it hasn't been done on your car for a while then have it done, it just removes excess carbon build up in the engine.

I'm not an owner but my mums car ('94 bluebird SSS) recently got a 200k service and that's some of the extra things the mechanic replaced.

Edited by INTNS
Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4032713
Share on other sites

the servicable items are all the same, except it is recommended to replace timing belt idler and tensioner, tensioner stud & bolt, timing case seals & water pump in the front. everything else is per usual. i would not go changing coils unless you have an issue. Get a diagnostic done to check sensor operation.

Hey all,

My 94 r33 gts-t Skyline is coming up to to its 200,000KM mark and was wondering do I need to get anything different done then a 100,000KM service?

And also if it is "worth" trying to add on more performance modifications if the KM's are this high.

I'm a car noob so please don't hurt me. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4032762
Share on other sites

depends on whats been done and what condition your cars in.

My '93 r33's coming up to its 190,000km birthday and still kicks ass.

Getting the timing belt done on monday, $980... Coils were replaced last service 185,000kms.Exhaust gaskets are getting a bit leaky so they'll be replaced too soon.

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4038463
Share on other sites

all it has done is heavy duty clutch, fmic, pod filter, atmos bov.

as for its condition the last time i got it serviced at xspeed the only thing they said was the rocker cover was leaking, although im not sure if they did a good job, they seemed a bit flaky...

I've noticed no problems driving apart from the usual atmospheric bov + gts-t stalling issue.

@grubb which timing kit?

thanks for the help

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4039478
Share on other sites

  • 3 weeks later...

The 200,000km service is a major, just as the 100,000km. On the engine side of things, the major components are:

  • Timing Belt
  • Timing Belt Bearings
  • Water Pump

I offer kits, that include genuine Nissan or OEM parts, and can be found within the following link:

http://www.skylinesaustralia.com/forums/Ni...vi-t137554.html

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4079574
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...