Jump to content
SAU Community

Recommended Posts

Hello

I have read peoples results after upgrading their RB20. Upgrades like turbos and fuel pumps and others. Many times I see that their rwkw is something like 140 or 150. I have read also that the stock rwkw for the RB20 in a GTS-T is 160rwkw. So why are people coming out with less than stock and happy about it?

Am I missing something?

Help

The factory kw rating is usually at the flywheel of the transmission not the wheels.

Transferring power from the flywheel to the wheels takes some of the engines power because it has to move the gears then the drive shaft then the axles.

For example the standard kw rating for a R33 Gtst is 183 kw but on my 33 which has all the supporting basic mods makes 181 kw *at the wheels*.

Ok

So my car is Rated a 160 kw but I get less than that at the wheels. So when people say with the R33 turbo on by R32 will make 180rwkw up too when done right, this means at the wheels correct? Kw is main, but rwkw is smaller actual to the wheels?

Yep basically right, you car uses power to spin the gearbox, flywheel, driveshafts, wheels etc.

RwKw is the power that actually gets to the ground.

So everyone here on the forums uses rwkw, its easier to measure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...