Jump to content
SAU Community

Recommended Posts

Paul - I think he is offering his service's if you provide him with the file?

Ignore me if you have already tried to get his help outside of this thread.

ive pm'd him the pdf...no reply as yet

Edited by DiRTgarage
  • 4 weeks later...
  • 2 weeks later...

If it is important maybe offer a financial incentive to people... always something for nothing.

One thing I have learned in Japan is that you pay for everything...

Edited by Laurence
If it is important maybe offer a financial incentive to people... always something for nothing.

One thing I have learned in Japan is that you pay for everything...

ohh well...name your price??

ive given hundreds of hours of free info on here from research ive done that has cost me thousands...but if $$ are required then someone cost it up for me.

Edited by DiRTgarage
I am not allowed to advertise commercial services as a non-sponsor! :P

Is it for a customer's car or yours?

does it really matter who its for ??

if you want to help then do so...if not why are you posting here?

only need to know in broken english what the instructions are for step 1 (the 1 in the round circle) and step 2. Its only two small pages in a very simple instruction booklet...not asking to have War and Peace translated into Swahili.

I can give you the basics pretty soon, just need a bit of time for the specifics... If you were in Brissie I'd prob suggest a 6-pack dropped around to me would help with the cause!

The only thing I'm initially worried about is that it looks very specific and I wouldn't want to give you the wrong info that would end up blowing someones engine.

Anyways I'll see what I can come up with and let you know how it goes.

Beau

P.S. I'm sure dodgy and Laurence prob have a bit better knowledge than me from seeing their translations too so that may be the way to go.

And I can see where Laurence is coming from asking whether its for a customer, because official translation services etc can be very expensive... maybe you should consider charging the customer for the service too.... again just a thought!

Edited by insanity

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...