Jump to content
SAU Community

What Is The Red Line On Stock R34 Gtr Dash?

Bakes

By Bakes,
in Engines & Forced Induction

 Share

Recommended Posts

Bakes Mentor

Bakes

Posted
  • Author
Posted

I could floor mine until it bounces off the rev limiter and find out I guess, lol. Im sure someone will know though.

I have my shift light on the MFD set up at ~6750 RPM. I got told you shouldnt rev past 7K revs on stock motor.

GTRsean Grand Master

GTRsean

Posted
Posted
remap ur ecu and u can goto 9000 ;)

Hmm..= more wear and tear. No extra power with stock cams and turbos, and oil pump wasn't designed to do those revs....

But if you have the $$$$$, go for it, rev it till it pops lol.

GTRsean Grand Master

GTRsean

Posted
Posted (edited)

Peak power stock is at around 6800rpm so 7k is a good point to shift. Reving em to 8k every now and again will not hurt em, but bouncing off the rev limiter ain't good from what I've read and seen.

Cheers

Edited by GTRsean
kefe69 Contributor

kefe69

Posted
Posted

Stock redline is 8k. I have nismo one now so it looks better. Rev light is set to 7700rpm. I always go to 8k cause when you change to next gear you always have that extra boost. Stock GTR was built for that very reason of going hard. Depending on mods you can always go past the 8k..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...