Jump to content
SAU Community

Recommended Posts

  • Replies 281
  • Created
  • Last Reply

Top Posters In This Topic

I was in until I checked what boost the car was holding (found it was down to mid 16psi) so fiddled with the actuator and broke the arm.

Rewelded the arm and then lost the custom made section that screws on to the actuators arm. :P

Not going to make another for the lazy 1bar actuator.

Picking up a 19psi actuator from MTQ tomorrow but don't like the chances of welding up another custom rod and then giving it a quick street tune in time.

Either way if the car is ready in time or not I'll be there. :D

I was in until I checked what boost the car was holding (found it was down to mid 16psi) so fiddled with the actuator and broke the arm.

Rewelded the arm and then lost the custom made section that screws on to the actuators arm. :)

Not going to make another for the lazy 1bar actuator.

Picking up a 19psi actuator from MTQ tomorrow but don't like the chances of welding up another custom rod and then giving it a quick street tune in time.

Either way if the car is ready in time or not I'll be there. :P

im still running the 18 actuator,

i took it to shaun on tuesday but when everthing is hot as hell its a joke to even contemplate getting in there.

so i wil change it in a few weeks when i have 2 hands again.

Its all good buddy.

Popped down to MTQ today and checked out the 19psi actuator. The seat pressure felt a tad soft and not much if any more than the 1bar actuator. Testing it she cracked off the seat around 12psi.

I checked out the slightly more expensive 14psi Large can and MFG I can't even lift the thing off its seat.

The larger can has a spring that is a shit load stiffer as the diaphram is larger so more surface area etc etc.

I went with that as it will hold against the flap pushing open much better.

Now to try and squeeze it in. :P

mitch dont be a bitch

put the thing on the dyno

i am sure you have given it shit on the streets

so a dyno run wont hurt

at least you will know how much u pulling without a proper tune

Its all good buddy.

Popped down to MTQ today and checked out the 19psi actuator. The seat pressure felt a tad soft and not much if any more than the 1bar actuator. Testing it she cracked off the seat around 12psi.

I checked out the slightly more expensive 14psi Large can and MFG I can't even lift the thing off its seat.

The larger can has a spring that is a shit load stiffer as the diaphram is larger so more surface area etc etc.

I went with that as it will hold against the flap pushing open much better.

Now to try and squeeze it in. :)

lol u should feel the 25.4 psi one i have

i will bring it with on saturday, if i remember for a show and tell between cars.

no no tune Krishy kindly lent me my old PFC so will run with that and at least crack 210ish should be more cause im trying to wind to boost up safely

unfortunately it was tuned on 10psi so 15psi see's it leaning out a little @ high rpm

anyone know how to road tune :blink:

oh also added 600rpm and it goes like a freight train when boost hits

mitch dont be a bitch

put the thing on the dyno

i am sure you have given it shit on the streets

so a dyno run wont hurt

at least you will know how much u pulling without a proper tune

i concur :blink:

what time is this saturday and can i rock up and pay ?

yeah you should be able to pay on the day rock up around 10am

i concur :D

yeah you should be able to pay on the day rock up around 10am

will have to see what happens

got a feeling im ment to be working but may call up saying i cannot attend work as i have to blow a commodore away :blink:

no no tune Krishy kindly lent me my old PFC so will run with that and at least crack 210ish should be more cause im trying to wind to boost up safely

unfortunately it was tuned on 10psi so 15psi see's it leaning out a little @ high rpm

anyone know how to road tune :blink:

oh also added 600rpm and it goes like a freight train when boost hits

watch your knock count on the hand controller dude.........keep it under 60 when boosting

Steve,

I'd be super careful on 1bar. 1bar 'should' be up around 240rwkwish and the injectors are only 370cc so only good for a little over 200rwkw before they are max'd and afr's start heading north.

On a side note here's my fat actuator. No more boost drop for me :blink:

Its mounted, bracket modded rod shortened etc now just have to cut and weld the screw on section that attaches the wastegate.

post-382-1227184004_thumb.jpg

post-382-1227184013_thumb.jpg

yeah will do guys i will double check the boost controller because it was set to the lowest and goes straight to about 15-16 on my gauge but my gauge is inaccurate by about 2psi

so will try it in the other way tomorrow or get rid of it

no no tune Krishy kindly lent me my old PFC so will run with that and at least crack 210ish should be more cause im trying to wind to boost up safely

unfortunately it was tuned on 10psi so 15psi see's it leaning out a little @ high rpm

anyone know how to road tune :blink:

oh also added 600rpm and it goes like a freight train when boost hits

I could plug in my dataloggit and wideband and go for quick blast if you like?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...